| | |
| | IMG-245980 |
|
| | |
| | IMG-289044 |
|
| | |
| | IMG-289045 |
|
| | |
| | IMG-289046 |
|
| | |
| | IMG-289047 |
|
| | |
| | IMG-289048 |
|
| | IMG-288844 |
|
| | IMG-289063 |
|
| | Illustration A Illustration B Illustration C |
| | IMG-289064 |
|
| | |
| | IMG-265409 |
|
| | |
| | IMG-265410 |
|
| | |
| | IMG-265411 |
|
| | |
| | IMG-288845 |
|
| | |
| | IMG-288846 |
|
| | |
| | IMG-265412 |
|
| | |
| | IMG-265413 |
|
| | Detach the motor by carefully prying up the catches at the side and underneath using a small screwdriver. Unhook the motor from the remaining catches and disconnect the connector. The motor will be reused.
|
| | |
| | IMG-265420 |
|
| | Installation Certain car models do not have the lighting function. On these models, install lamp and lens. Take a new mirror housing, bulb and lamp lens for ground lighting from the kit. Remove the cable with the lamp holder from the mirror. Insert a bulb into the holder.
|
| | IMG-265421 |
|
| | |
| | IMG-265422 |
|
| | |
| | IMG-288847 |
|
| | |
| | IMG-288848 |
|
| | |
| | IMG-265414 |
|
| | |
| | IMG-265415 |
|
| | |
| | IMG-265416 |
|
| | IMG-265417 |
|
| | IMG-265418 |
|
| | Illustration A Illustration B Illustration C |
| | IMG-265419 |
|
| | Connect the wiring to the old mirror glass. Ensure that the white damper blades align in their grooves. Press the mirror glass into place.
|
| | IMG-289083 |
|
| | Steps 24-28 apply to cars without high level control module. |
| | IMG-289084 |
|
| | |
| | IMG-289085 |
|
| | IMG-289086 |
|
| | Illustration A Two of the rivets (1) end up at the bottom on the door, the last rivet (2) ends up inside the console. To prevent rivet remains from rattling inside the door, carry out the following: Illustration B |
| | IMG-289283 |
|
| | |
| | IMG-289284 |
|
| | |
| | IMG-289285 |
|
| | |
| | IMG-289286 |
|
| | IMG-288850 |
|
| | IMG-289288 |
|
| | Illustration A Check that the clips around the panel are intact and correctly positioned, they are detachable. Connect the connectors to the door module.
Illustration B Illustration C Align the clips carefully in the holes in the door frame and press securely. Tighten the panel using the two screws, tightening torque 5 Nm (4 lbf.ft.).
|
| | IMG-289287 |
|
| | |
| | IMG-289289 |
|
| | |
| | IMG-289290 |
|
| | |
| | IMG-289291 |
|
| | |
| | |
| | IMG-242268 |
|
| | In cases where the driver's door module (DDM) has been replaced, download software according to the service information in VIDA. Download software (application) for the accessory's function according to service information in VIDA. See VIDA or accessories catalogue for article number on software. Initiate the power windows according to: VIDA Diagnostics Vehicle communication Advanced DDM Initiating windows Initiating front door windows
|