Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

There may be parts in the accessories kit that are not needed for this installation.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

7. Used for accessory components.

Disconnecting the battery

Open the tailgate.

Remove the marked part.

Loosen the nut.

Remove the battery's negative cable.

Removal

Remove the marked part.

Remove the marked part.

Release the lock.

Remove the marked part.

Use: Interior trim remover

Disconnect the connector.

Remove the screw.

1. 
   Tightening torque: Sill moulding without cargo anchor , 8 Nm
   

2. 
   Tightening torque: Sill moulding with cargo anchor , 24 Nm
   

Repeat on the other side.

Lift the marked component up

Disconnect the connector.

Remove the nuts.

Remove the clips.

Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones.

1. Release the lock.

2. Remove the marked part.

Fold marked part aside.

Remove the marked part.

Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Remove the screw.

Tightening torque: Cargo anchor, to body , 24 Nm

Remove the marked part.

The graphic shows the back of the component.

Disconnect the connector.

Remove the screws.

Remove the screws.

Remove the nut.

Fold the wing liner aside.

Remove the screw.

Loosen the component indicated. Do not remove it.

Loosen the component indicated. Do not remove it.

Repeat the steps when removing on opposite side.

Locate the connector.

Disconnect the connector.

Remove the marked part.

Remove the nuts.

The part is to be reused.

Repeat on the other side.

Remove the marked part.

The part is not to be reused.

Remove the marked detail/details.

The part is not to be reused.

Remove the marked part.

The part is not to be reused.

Accessory installation

Use detail according to image.

Remove the marked detail/details.

The part is not to be reused.

Route the wiring harness into the passenger compartment.

Install component that comes with the accessory kit.

Install the nuts

Repeat on the other side.

Install component that comes with the accessory kit.

Repeat on the other side.

Tighten the nuts.

Tighten the screw.

Tightening torque: Tow hitch member mounting to body frame
Stage 1: 50 Nm
Stage 2: 30 Degree

Repeat on the other side.

Connect the connector.

Fasten the wiring harness using the existing clips.

Fasten the wiring harness using the existing clips.

Connect the connector.

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

Vehicles with Twin Engine

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

All vehicles

Clean the surface.

Use: , Isopropanol

Clean the surfaces.

Use: , Isopropanol

Remove the protective film.

Measure

Install components that come with the accessory kit.

Locate the pre-routed connectors.

Connect the connectors.

Connect the recently installed cables.

Remove the protective film.

Install component that comes with the accessory kit.

Remove the nut.

The part is to be reused.

Connect the prerouted cable.

Install the nut.

Tightening torque: M6 , 10 Nm

Fasten the wiring harness using the existing clips.

Release the lock.

Remove the marked part.

Install component that comes with the accessory kit.

Install components that come with the accessory kit.

Reinstall the removed part.

Vehicles without power outlet

Print template from Service Product Journal (SPJ) 34548.

Cut following the dotted lines.

Locate relevant marking.

Place the template according to image

Mark using a pen

Measure

Check the value.

Make a hole, using the tool indicated.

Remove the marked part.

Use: Air-powered air saw

Vehicles with power outlet

Print template from Service Product Journal (SPJ) 34548.

Cut following the dotted lines.

Locate relevant marking.

Place the template according to image

Mark using a pen

Measure

Check the value.

Make a hole, using the tool indicated.

Remove the marked part.

Use: Air-powered air saw

All vehicles

Install component that comes with the accessory kit.

Connect the prerouted cable.

Connect the connector.

Connecting the battery

Reinstall the battery's negative cable.

Tighten the nut.

Tightening torque: Battery cable for battery , 6 Nm

Installation

Reinstall the removed parts in reverse order.

Accessory installation

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 30795625

Check

Press the button.

Fold out the towbar.

If the components rub against each other, adjustments must be made to correct this.

1. Left indicator lamp

2. Fog tail lamps.

3. Ground connection

4. Right indicator lamp

5. Right position lamp

6. Brake light

7. Left position lamp

8. Back-up lamp

9. Battery voltage, constant

10. Battery voltage, ignition on

11. Ground connection

12. Not connected

13. Ground connection

Press the button.

Fold in the towbar.