| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
|  | | IMG-363036 |
|
| | Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
|  | | IMG-394535 |
|
| | |
| | |
| | Note!
The removal steps may contain installation details. |
|
|  | | IMG-417434 |
|
| | Note!
Perform the procedure one side at a time. |
Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304
Disconnect the connector. |
|  | | IMG-417437 |
|
| | |
|  | | IMG-417438 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
|  | | IMG-417439 |
|
| | |
|  | | IMG-417440 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
|  | | IMG-419055 |
|
| | Remove the screws. Remove the panel. |
|  | | IMG-419056 |
|
| | |
|  | | IMG-414613 |
|
| | |
|  | | IMG-419060 |
|
| | Remove the panel. Repeated on the right-hand side. |
|  | | IMG-419061 |
|
| | Repeated on the right-hand side. |
|  | | IMG-419062 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-419063 |
|
| | Detach the panel. Use hands only. Repeated on the right-hand side. |
|  | | IMG-419065 |
|
| | Release the catch. Remove the marked part. Repeated on the right-hand side. |
|  | | IMG-419066 |
|
| | Remove the panel. Use hands only. |
|  | | IMG-419067 |
|
| | Remove the screw.
Tightening torque: M6
, 10 Nm
Repeated on the right-hand side. |
|  | | IMG-417441 |
|
| | Release the lock. Repeat on the other side. Remove the marked part. |
|  | | IMG-417504 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
|  | | IMG-422035 |
|
| | Caution!
Make sure that the seat backrest upholstery (fold down position) is not damaged by contact with the floor! |
|
|  | | IMG-422102 |
|
| | |
|  | | IMG-417505 |
|
| | |
|  | | IMG-401577 |
|
| | |
|  | | IMG-401579 |
|
| | |
|  | | IMG-401580 |
|
| | |
|  | | IMG-401581 |
|
| | |
|  | | IMG-417510 |
|
| | |
|  | | IMG-401583 |
|
| | |
|  | | IMG-401584 |
|
| | |
|  | | IMG-396605 |
|
| | Disconnect the connector. |
|  | | IMG-396606 |
|
| | Unhook the cable harness clips. |
|  | | IMG-417535 |
|
| | |
|  | | IMG-407110 |
|
| | |
|  | | IMG-414611 |
|
| | |
|  | | IMG-415830 |
|
| | Repeat on the other side. |
|  | | IMG-415831 |
|
| | Remove the screw.
Tightening torque: M6
, 10 Nm
Repeat on the other side. |
|  | | IMG-416086 |
|
| | |
|  | | IMG-416087 |
|
| | |
| | Vehicles with keyless entry |
|  | | IMG-413321 |
|
| | |
| | |
|  | | IMG-415835 |
|
| | |
|  | | IMG-416089 |
|
| | |
|  | | IMG-419165 |
|
| | Remove the panel. Disconnect any connector(s). Repeated on the right-hand side. |
|  | | IMG-419172 |
|
| | |
|  | | IMG-419173 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-419205 |
|
| | |
|  | | IMG-418626 |
|
| | |
|  | | IMG-418631 |
|
| | |
|  | | IMG-418634 |
|
| | Remove the screws. Remove the panel. |
|  | | IMG-418641 |
|
| | Disconnect the connector. |
|  | | IMG-418643 |
|
| | Loosen the screws. Loosen the exact number of turns indicated in the image. |
|  | | IMG-418645 |
|
| | Use: Interior trim remover
The part is not to be reused. |
| | |
|  | | IMG-419877 |
|
| | |
|  | | IMG-418648 |
|
| | Tighten the bolts.
Use special tool: T9814199, Torque wrench
|
|  | | IMG-418642 |
|
| | |
|  | | IMG-419360 |
|
| | Loosen the marked detail/details. To be repeated in the other end of the component. |
|  | | IMG-419361 |
|
| | Release the catches. Loosen the marked detail/details. Use: Scribe
Use: Interior trim remover
To be repeated in the other end of the component. |
|  | | IMG-419675 |
|
| | Use: 988734, Cable tie, 750 mm
|
|  | | IMG-419680 |
|
| | |
|  | | IMG-419830 |
|
| | |
|  | | IMG-419831 |
|
| | |
|  | | IMG-419862 |
|
| | Position/route the cable as illustrated. Install the cable. Use a cable tie |
|  | | IMG-419832 |
|
| | Turn once. Tear off the excess foam tape. |
|  | | IMG-419833 |
|
| | Pull the wiring through. Use: 1161150, Lubricant
Wipe off Remove the cable tie(s). |
|  | | IMG-419834 |
|
| | |
|  | | IMG-419365 |
|
| | Reinstall the removed part. To be repeated in the other end of the component. |
|  | | IMG-419362 |
|
| | Caution!
Make sure that the rubber grommet seals properly to the body. |
Reinstall the removed part. To be repeated in the other end of the component. |
|  | | IMG-419416 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | |
|  | | IMG-418722 |
|
| | |
|  | | IMG-416273 |
|
| | Remove the nut. Fold marked part aside. |
|  | | IMG-416275 |
|
| | Release the catches. Fold marked part aside. |
|  | | IMG-389347 |
|
| | |
| | |
|  | | IMG-389346 |
|
| | |
|  | | IMG-389348 |
|
| | Reinstall the removed part. |
|  | | IMG-402750 |
|
| | Install the cable. Use a cable tie |
|  | | IMG-416277 |
|
| | Reinstall the removed part. |
|  | | IMG-416317 |
|
| | Install component that comes with the accessory kit. |
|  | | IMG-417882 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
|  | | IMG-419549 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
|  | | IMG-419481 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
|  | | IMG-419485 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
|  | | IMG-419555 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
|  | | IMG-419556 |
|
| | Route the wires adjacent to existing wirings. Install the cables. Use a cable tie |
|  | | IMG-419557 |
|
| | Route the wires adjacent to existing wirings. Install the cables. Use a cable tie |
|  | | IMG-419476 |
|
| | Route the wires adjacent to existing wirings. Install the cables. Use a cable tie |
|  | | IMG-417598 |
|
| | Position/route the cables as illustrated. |
|  | | IMG-417599 |
|
| | Note!
Route the wiring between floor carpet and air duct. |
Position/route the cables as illustrated. |
|  | | IMG-418163 |
|
| | |
|  | | IMG-418167 |
|
| | Remove the marked part. The part is not to be reused. |
|  | | IMG-418225 |
|
| | |
|  | | IMG-418227 |
|
| | Position/route the cables as illustrated. |
|  | | IMG-419775 |
|
| | Install the cables. Use a cable tie |
|  | | IMG-418228 |
|
| | Position/route the cables as illustrated. |
|  | | IMG-418248 |
|
| | |
|  | | IMG-418243 |
|
| | |
|  | | IMG-418242 |
|
| | |
|  | | IMG-419769 |
|
| | Connect the prerouted cable. Position/route the cable as illustrated. |
|  | | IMG-419772 |
|
| | Caution!
Make sure that the wire is not bent to a radius of less than 5 mm. |
Position the cable harness excess as illustrated. Install the cable. Use a cable tie |
|  | | IMG-419770 |
|
| | Connect the prerouted cable. Position/route the cable as illustrated. |
|  | | IMG-418236 |
|
| | Connect the cable. Position/route the cable as illustrated. |
|  | | IMG-418257 |
|
| | |
|  | | IMG-388631 |
|
| | |
|  | | IMG-388638 |
|
| | |
|  | | IMG-388639 |
|
| | Connect the prerouted cable. Install the nut.
Tightening torque: M6
, 10 Nm
|
|  | | IMG-388633 |
|
| | |
|  | | IMG-418300 |
|
| | |
|  | | IMG-418303 |
|
| | |
|  | | IMG-419252 |
|
| | Release the connector's catch. Release the lock. Disconnect the connector.
|
|  | | IMG-419255 |
|
| | Release the connector's catch. Remove the connector from its attachment. |
|  | | IMG-416447 |
|
| | |
|  | | IMG-397975 |
|
| | |
|  | | IMG-416490 |
|
| | |
|  | | IMG-374930 |
|
| |
Use special tool: T9512620, Stripping tool (for wiring)
|
|  | | IMG-374928 |
|
| | |
|  | | IMG-398784 |
|
| |
Use special tool: T9512785, Crimping tool (included in 9512669)
|
|  | | IMG-398782 |
|
| |
Use special tool: T9512785, Crimping tool (included in 9512669)
|
|  | | IMG-326808 |
|
| | Caution!
Make sure that the surrounding components are protected from heat. |
Use special tool: T9512777, Hot-air gun
|
|  | | IMG-397870 |
|
| | |
|  | | IMG-419256 |
|
| | Install the connector to its attachment. |
|  | | IMG-419257 |
|
| | |
|  | | IMG-418319 |
|
| | Caution!
Make sure that no part of the wiring harness is trapped. |
Reinstall the removed part. |
|  | | IMG-418318 |
|
| | Note!
Extra cable length must be secured using cable ties. |
Position/route the cable as illustrated. |
|  | | IMG-418315 |
|
| | Position/route the cable as illustrated. Install the cable. Use a cable tie |
|  | | IMG-418316 |
|
| | Position/route the cable as illustrated. |
|  | | IMG-415163 |
|
| | Connect the prerouted cable. |
|  | | IMG-418231 |
|
| | Install component that comes with the accessory kit. |
|  | | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number. |
| | |
|  | | IMG-400000 |
|
| | Reinstall the removed parts in reverse order. |
