2011 R.H.D

安裝說明

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
V60 2011
V60 (-18) 2011

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313202951.431414410, 31399404, 31399405, 31399406, 31399407, 31399408, 31399409, 31399410, 31399411, 31399412, 31399413, 31399414, 31373272, 31373276, 31373280, 31373284, 31373288, 1287635, 1287634, 31320169, 31320167, 31320168, 31320166, 31320170, 31320302, 31320303
Multimedia system, RSE, two screens, with two players




Equipment
IMG-242205
A0000162
IMG-239664

IMG-382145

IMG-382146


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Note!

Some steps in these installation instructions are presented with illustration only.


1
IMG-329148
 

2
IMG-340979
 

3
IMG-340980
 

  • Tightening torque screws: 40 Nm (29.5 lbf.ft.).

4
IMG-303005
 

5
IMG-303006
 

  • Tightening torque screws: 40 Nm (29.5 lbf.ft.).

  • Repeat the method steps for the other seat.

6
IMG-332179
 

  • Set the ignition key to position 0.

  • Disconnect the battery negative lead.


Note!

Wait at least three minutes before unplugging the connectors or removing other electrical equipment.



Note!

The SRS system remains active for a brief period after power is disconnected. Thus, wait three minutes before starting work.


7
IMG-329151
 

8
IMG-329209
 

  • Loosen the connector by screwing out the screw.

9
IMG-329152
 

Applies to seat without belt tensioner.

10
IMG-330333
 

Applies to seat with belt tensioner.

11
IMG-330334
 

12
IMG-329153
 

Applies to all models


Caution!

Exercise care when doing this so that the trim is not damaged.


  • Lift out seat.

  • Repeat the method steps for the other seat.

13
IMG-292826
 

14
IMG-292804
 

15
IMG-344791
 

16
IMG-344796
 

17
IMG-344818
 

  • Use tape to protect the tunnel console.

18
IMG-293021
 

19
IMG-293022
 

20
IMG-293023
 

21
IMG-303385
 

22
IMG-339921
 

  • Unplug the connector.

23
IMG-293024
 

24
IMG-293025
 

Applies to vehicles with headset sockets

25
IMG-293026
 

26
IMG-329163
 

Applies to all models

27
IMG-293028
 

28
IMG-293029
 

29
IMG-329164
 

30
IMG-344819
 

31
IMG-344825
 

32
IMG-344827
 

33
IMG-344828
 

  • Secure the part with butyl tape.

34
IMG-329435
 

35
IMG-329164
 

  • Reinstall the removed parts.

  • Ensure that no part of the cable harness is trapped.

36
IMG-330503
 

  • Secure the cable marked "Right side" with a cable tie.

37
IMG-344829
 

38
IMG-344830
 

39
IMG-344831
 

  • Position the control module as illustrated.

40
IMG-344832
 

  • Position the excess as illustrated.

41
IMG-329448
 

  • Route the cable marked "Left Side" between air duct and climate unit over to the left side.

42
IMG-344833
 

  • Position the cable harness as illustrated.

43
IMG-340508
 

44
IMG-344834
 

45
IMG-344835
 

46
IMG-344836
 

47
IMG-344837
 

48
IMG-330574
 

  • Secure the cable marked "Left side" with a cable tie.

49
IMG-344841
 

50
IMG-344843
 

51
IMG-344844
 

  • Route the cable marked "Right side" between air duct and climate unit over to the right side.

52
IMG-344845
 

  • Position the cable harness.

53
IMG-344846
 

54
IMG-330705
 

  • Secure the 2 cables at the existing cable harness using a cable tie.

55
IMG-344847
 

56
IMG-330708
 

  • Secure the 2 cables at the existing cable harness using a cable tie.

57
IMG-268413
 

  • Remove the knob for the lumbar support adjustment by removing the cover using a small screwdriver and pull the knob straight off.

58
IMG-337621
 

  • Take a long cable tie and thread it from the hole for lumbar adjustment and up to the hole for the head restraint's inner mounting. The cable tie must be routed between the upholstery and the protection.

59
IMG-337624
 

  • Take the head restraint marked "Passenger side".

  • Position the head restraint as illustrated.

60
IMG-338008
 

Applies when installing on the left-hand seat

  • Pull the zip fastener forward.

61
IMG-338009
 

62
IMG-344888
 

  • Transfer the cables to the opposite side.

63
IMG-344887
 

  • Close the zip fastener.

  • Fold the excess back.

64
IMG-337627
 

Applies to all models

  • Tape the cables to the cable tie.

65
IMG-337623
 

  • Place the head restraint in the seat.


Note!

The cables must be in front of the head restraint tube.


66
IMG-337625
 

  • Push the head restraint in to place at the same time as feeding the cables forward.

67
IMG-344851
 


Caution!

Check that the head restraint has locked into place by pulling it upwards.


68
IMG-262956
 

  • Using your fingers, press the cables under the protection. The cables must not press out the upholstery after installation.

    Padding (1)

    Padding (2)


Note!

The image shows a seat without upholstery.


69
IMG-337622
 

  • Pull the cable tie with cables through the hole and out at the lower edge.

  • Remove the cable tie and tape from the cable harness.

70
IMG-344892
 

  • Pull the cables forward and in under the seat. Follow the existing cable.

  • Secure the cables using three cable ties.

  • Reinstall the lumbar adjustment.


Note!

The image shows a seat without upholstery.


71
IMG-329473
 

  • Place the seat in the vehicle.

72
IMG-344852
 

  • Connect the 2-pin connector.

73
IMG-330728
 

  • Connect the green connector.

  • The groove and the arrow should be opposite each other.

74
IMG-330729
 

  • Connect the black connector.

  • The grooves should be opposite each other.

75
IMG-330730
 

  • Install the connector casings.

76
IMG-330731
 

  • Install cable ties around the connector casings.

77
IMG-329270
 

78
IMG-329268
 

79
IMG-329269
 

  • Repeat the method steps for the other seat.

80
 

  • Reinstall the detached components in reverse order.

81
IMG-336901
 

  • Reconnect the battery negative lead

82
IMG-336904
 


Warning!

When the ignition is to be switched on for the first time after the battery has been disconnected, this must be done whilst by standing outside the vehicle, stretching your arm in and avoiding the working area for the airbags.


  • Set the ignition switch to position II.

83
IMG-352549
 

  • Install the batteries in the remote control and headsets.

84
IMG-275777
 

  • Region code the DVD players. Information is available in VIDA under:

    • Product specifications

    Design and Function

    3 Electrical system

    39 Media - communication and entertainment

    393 Equipment for entertainment

    Rear seat entertainment system

    Design

  • Place remote control, headsets, cable harness, and quick-guide in a suitable place in the vehicles.

© Volvo Car CorporationMultimedia system, RSE, two screens, with two players- 31320295 - V1.4
volvocars.com
Lifestyle Collection
English
找尋經銷商
Hong Kong

Cookies 資料檔 法律聲明 隱私政策 版權所有

Copyright © 2024 Volvo Cars. All rights reserved.