| | |
| | IMG-247309 |
|
| | Preparations Passenger compartment |
| | IMG-239420 |
|
| | |
| | IMG-249172 |
|
| | |
| | IMG-222267 |
|
| | |
| | IMG-231433 |
|
| | |
| | IMG-222268 |
|
| | |
| | IMG-225205 |
|
| | |
| | IMG-225201 |
|
| | |
| | IMG-239483 |
|
| | Move the carpeting aside. Make a cut in the thick insulating mat starting level with the blue connector of the central electronic module (CEM) and then continue straight down. Move aside the insulating mat to access the grommet.
|
| | IMG-249173 |
|
| | |
| | IMG-249176 |
|
| | |
| | IMG-249174 |
|
| | Remove the rear sill trim panel by pulling it up at the front edge (1) and then unhooking it from the clip (2). Push the side cushion at the lower edge to one side and pull the panel so that the hook (3) releases.
|
| | IMG-249175 |
|
| | |
| | |
| | IMG-273525 |
|
| | |
| | IMG-273526 |
|
| | |
| | IMG-268004 |
|
| | |
| | IMG-268005 |
|
| | |
| | IMG-259759 |
|
| | Applies to right-hand drive cars Remove the two screws on the tailgate sill trim panel.
|
| | IMG-259760 |
|
| | Applies to right-hand drive cars Carefully pull off the panel, it is secured by six clips.
|
| | IMG-273316 |
|
| | |
| | |
| | IMG-232587 |
|
| | |
| | IMG-232588 |
|
| | |
| | IMG-273529 |
|
| | |
| | IMG-273530 |
|
| | |
| | IMG-236054 |
|
| | |
| | |
| | IMG-273531 |
|
| | Steps 26-29 are carried out on both sides. Apply tape to the front edge of the wing extender to protect it.
|
| | IMG-273532 |
|
| | |
| | IMG-273533 |
|
| | |
| | IMG-273534 |
|
| | |
| | IMG-273535 |
|
| | Steps 30-33 apply to cars with headlamp washing Push the wing liner to one side on the left to access the connector on the deflector.
|
| | IMG-273537 |
|
| | |
| | IMG-273538 |
|
| | Place a container under the car. Release the catch (1) on the connection for the washer pump. Pull the connection (2) straight out. Allow the washer fluid to run into the container. Alternatively, plug the connection on the pump using a suitable rubber plug.
|
| | IMG-273539 |
|
| | |
| | IMG-273543 |
|
| | |
| | IMG-273544 |
|
| | Remove the bumper cover by pulling it straight forward until all hooks release. At the same time disconnect the connectors for the fog lamps. Place the cover on a suitable surface with the outer side facing down. This procedure is easier carried out by two people.
|
| | IMG-273545 |
|
| | |
| | IMG-273546 |
|
| | |
| | IMG-273547 |
|
| | |
| | |
| | IMG-273550 |
|
| | |
| | IMG-273551 |
|
| | |
| | IMG-273552 |
|
| | Applies to left-hand drive cars Take the cable harness from the kit and connect it to the sensors. The large connector must be on the right-hand side of the cover.
|
| | IMG-273554 |
|
| | Applies to right-hand drive cars Take the cable harness from the kit and connect it to the sensors. The large connector must be on the left-hand side of the cover.
|
| | IMG-273555 |
|
| | |
| | IMG-273556 |
|
| | |
| | IMG-273557 |
|
| | Applies to cars with headlamp washing Secure the cable harness using cable ties at the existing clips.
|
| | IMG-273558 |
|
| | Take the short cable harness from the kit. Remove the taped connector from the cable harness. Pull the cable harness from underneath and up to at the rear edge of the headlamp. Allow the connector to hand down as illustrated.
|
| | IMG-273559 |
|
| | |
| | IMG-273560 |
|
| | Connect the cable harness from the sensors. Press the connector into intended holes on the deflector. Install the bumper cover by repeating points 26 - 34 in reverse order.
|
| | IMG-273561 |
|
| | |
| | |
| | IMG-235947 |
|
| | Steps 50–54 apply to left-hand drive cars Note!
Make sure that the cable is positioned so that it is not damaged by heat or wear. |
|
| | |
| | IMG-273585 |
|
| | Applies to 6 cylinder engines Remove the engine cover by pulling it straight up.
|
| | IMG-273586 |
|
| | |
| | IMG-273587 |
|
| | |
| | IMG-273588 |
|
| | |
| | IMG-273585 |
|
| | Steps 55–57 apply to right-hand drive cars Applies to 6-cyl engines and diesel engines Remove the engine cover by pulling it straight up.
|
| | IMG-273589 |
|
| | |
| | IMG-273590 |
|
| | Route the cable harness in-between the battery box and insulation for the cowl panel, and down to the rubber grommet. Secure using a cable ties on the outgoing cable harness from the battery box.
Note!
Make sure that the cable is positioned so that it is not damaged by heat or wear. |
Reinstall the headlamp.
|
| | |
| | IMG-235950 |
|
| | Applies to all models Cut off a small rubber nipple on the new rubber grommet. Lubricate the cable using soap solution and insert. Pull the cable into the passenger compartment. Adjust the length. Install the rubber grommet and move the heat shield on the cable towards the rubber grommet. Reinstall the engine splash guard and cover panel for the bumper. Lower the car. Reinstall the engine cover.
|
| | J3703487 |
|
| | Applies to left-hand drive cars Take the connector that was taped and connect it to the cable harness that was routed into the passenger compartment. Install the cable ends' pins in the connector as illustrated:
Blue (BL) Green (GN) Violet (VO) Yellow (Y) White (W) Black (SB)
|
| | IMG-249180 |
|
| | Applies to right-hand drive cars Take the connector that was taped and connect it to the cable harness that was routed into the passenger compartment. Install the cable ends' pins in the connector as illustrated:
Blue (BL) Black (SB) Violet (VO) White (W) Yellow (Y) Green (GN)
|
| | IMG-249181 |
|
| | |
| | IMG-249182 |
|
| | |
| | IMG-273591 |
|
| | |
| | IMG-273592 |
|
| | |
| | IMG-273593 |
|
| | |
| | IMG-242268 |
|
| | Reinstall: the glove box the sound barrier the sill trim panels the end face panel the rear seat cushion.
|