Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

There may be parts in the accessories kit that are not needed for this installation.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

7. Used for accessory components.

Removal

Remove the panel.

Repeat on the other side.

Remove the panel.

Repeat on the other side.

Remove the screw.

Remove the marked part.

Use hands only.

Repeat on the other side.

Remove the panel.

Repeat on the other side.

Remove the marked part.

Disconnect the connector.

Remove the screws.

Remove the marked part.

Cars with automatic transmissions

Release the shift-lock function.

All vehicles

Remove the part carefully

Remove the screws.

Detach the panel.

Disconnect the connector.

Remove the panel.

Remove the screws.

Remove the marked part.

Disconnect the connectors.

Repeat on the other side.

Vehicles with heated rear seat

Locate the connector.

Disconnect the connector.

Repeat on the other side.

All vehicles

Repeat on the other side.

Remove the marked part.

Remove the screws.

Repeat on the other side.

Tightening torque: Front seat to body , 40 Nm

Repeat on the other side.

1. Release the catch.

2. Remove the marked part.

Use: Electrician's screwdriver

Repeat on the other side.

Remove the screws.

Repeat on the other side.

Tightening torque: Front seat to body , 40 Nm

Repeat on the other side.

Loosen the screws.

Disconnect the connector.

Repeat on the other side.

Remove the screws.

Fold marked part aside.

Tightening torque: M6 , 10 Nm

Remove the marked part.

Remove the marked part.

Remove the screws.

Use hands only.

Loosen the component indicated. Do not remove it.

Disconnect the connectors.

Remove the marked part.

Remove the screws.

Fold marked part aside.

Tightening torque: M6 , 10 Nm

Remove the marked part.

Remove the panel.

Remove the panel.

Remove the marked part.

Repeat on the other side.

Remove the screws.

Remove the panel.

Remove the panel.

Remove the screw.

Repeat on the other side.

Remove the screws.

Remove the marked part.

Carefully pry loose the bottom edge of the panel and then continue around the panel.

Disconnect the connector.

Remove the panel.

Fold marked part aside.

Remove the nut.

Remove the marked part.

Use special tool: T9814088, Puller

Disconnect the connector.

Remove the screws.

Remove the marked part.

Disconnect the connector.

Remove the nuts.

Tightening torque: M6 , 10 Nm

Remove the marked part.

Use hands only.

Remove the screws.

Remove the panel.

Use hands only.

Detach the panel.

Disconnect the connector.

Remove the panel.

Remove the panel.

Remove the fasteners.

Remove the insulation material.

Remove the nuts.

Fold the insulation aside.

Accessory installation

Use details according to image.

Ensure that all clips engage.

Install the nuts

Tightening torque: M6 , 10 Nm

Use: 988734, Cable tie, 750 mm

Use detail according to image.

Tape the cables on the cable tie.

Pull the wiring harness through.

Pull the wiring harness through.

Route the ground wire next to the existing wiring harness.

Remove the screw.

Connect the prerouted cable.

Reinstall the screw.

Use a cable tie

Tightening torque: M6 , 10 Nm

Use detail according to image.

Release the connector's secondary lock.

Lift approximately 2 mm.

Note the position.

Connect the numbered terminal to the corresponding figure in the connector.

Press until a click is heard.

Connect the connector.

Route the wire adjacent to existing wirings.

Use a cable tie

Route the wire adjacent to existing wirings.

Use a cable tie

Disconnect the connector.

Fold marked part aside.

Position/route the cables as illustrated.

Use a cable tie

Route the wire adjacent to existing wirings.

Use a cable tie

Route the wire adjacent to existing wirings.

Use a cable tie

Route the wire adjacent to existing wirings.

Use a cable tie

Detach and fold back the floor covering.

Route the wire adjacent to existing wirings.

Use a cable tie

Fold the floor carpet back.

Route the wire adjacent to existing wirings.

Use a cable tie

Position/route the cable as illustrated.

Route the wire adjacent to existing wirings.

Use a cable tie

Connect the prerouted cable.

Route the wire adjacent to existing wirings.

Use a cable tie

Removal

Release the catches.

Remove the marked part.

Remove the screw.

1. Release the catch.

2. Release the lock.

3. Remove the marked part.

Installation

Note the position.

Connect the prerouted cable.

Install component that comes with the accessory kit.

Accessory installation

Route the wire adjacent to existing wirings.

Use a cable tie

Position/route the cable as illustrated.

Use a cable tie

Removal

1. Depress the locking devices.

2. Release the connector's catch.

Disconnect the connector.

Adjust to the lowermost position.

Remove the marked part.

1. Release the catches.

2. Remove the marked part.

Installation

Connect the numbered terminal to the corresponding figure in the connector.

Reinstall the removed parts in reverse order.

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.