| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | After installation, the car must not be washed for 48 hours When installing, the car must retain a temperature of 20 degrees C. After installation, the car must not be driven for 2 hours |
| | |
| | IMG-363036 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | |
| | IMG-373951 |
|
| | |
| | IMG-344142 |
|
| | Clean the surface. Use: 1161721, Isopropanol
|
| | IMG-344141 |
|
| | Matt the surface gently. Use: , Sand paper P1000
|
| | IMG-344142 |
|
| | Clean the surface. Use: 1161721, Isopropanol
|
| | IMG-344251 |
|
| | Note! Paint the sensors the same colour code as the vehicle. |
Use: , Volvo Original Touch-up paint
Use base coat only. Use: 31335447, Varnish 2-component
Also see the instructions on the container. |
| | IMG-333934 |
|
| | Caution! First the paint must dry after painting. |
|
| | |
| | IMG-332193 |
|
| | Set the ignition key to position 0. |
| | IMG-371925 |
|
| | |
| | IMG-372212 |
|
| | Measure and mark as illustrated. |
| | IMG-372210 |
|
| | |
| | IMG-372209 |
|
| | Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304
|
| | IMG-372207 |
|
| | |
| | |
| | IMG-372208 |
|
| | |
| | |
| | IMG-356526 |
|
| | |
| | IMG-356597 |
|
| | |
| | IMG-356582 |
|
| | |
| | IMG-366013 |
|
| | |
| | |
| | IMG-373525 |
|
| | |
| | IMG-377735 |
|
| | If a relay is installed in the slot indicated, nothing further needs to be done regarding the fuse box. If no relay is installed in the slot indicated, relay and fuse must be installed as shown below. |
| | IMG-377778 |
|
| | |
| | IMG-377754 |
|
| | Reinstall the removed part. |
| | |
| | IMG-354413 |
|
| | |
| | IMG-372410 |
|
| | Repeat on the other side. |
| | IMG-372405 |
|
| | Remove the screws. Repeat on the other side. |
| | IMG-374150 |
|
| | |
| | IMG-355092 |
|
| | Repeat on the other side. |
| | IMG-357976 |
|
| | Repeat on the other side. |
| | IMG-355184 |
|
| | Note! This step is easier with two people. |
Release the connector's catch. Disconnect the connector. |
| | IMG-355166 |
|
| | Caution! Place the Bumper Cover on a suitable surface. |
Note! This step is easier with two people. |
|
| | |
| | IMG-373903 |
|
| | Locate the markings for the positions. |
| | IMG-373904 |
|
| | |
| | IMG-373905 |
|
| | |
| | IMG-373906 |
|
| | Caution! Sharp end of tool must be on outside of cover. |
Use special tool: T9997234, Hole stamp
|
| | IMG-373909 |
|
| | Clean the surfaces. Use: 1161721, Isopropanol
|
| | IMG-373913 |
|
| | Apply a thin and even layer. Use: 1161765, Primer
Allow to dry for at least 2 minutes, but no more than 60minutes. |
| | IMG-373914 |
|
| | Apply a thin and even layer. Use: 1161765, Primer
Allow to dry for at least 2 minutes, but no more than 60minutes. |
| | IMG-373916 |
|
| | Apply a thin and even layer. Use: 1161765, Primer
Allow to dry for at least 2 minutes, but no more than 60minutes. |
| | IMG-373957 |
|
| | Clean the surfaces. Use: 1161721, Isopropanol
|
| | IMG-373958 |
|
| | Apply a thin and even layer. Use: 8637076, Activator
Allow to dry for at least 10 minutes. |
| | IMG-373959 |
|
| | Clean the surfaces. Use: 1161721, Isopropanol
|
| | IMG-373960 |
|
| | Apply a thin and even layer. Use: 8637076, Activator
Allow to dry for at least 10 minutes. |
| | IMG-373926 |
|
| | Clean the surface. Use: 1161721, Isopropanol
|
| | IMG-373927 |
|
| | Clean the surface. Use: 1161721, Isopropanol
|
| | IMG-373928 |
|
| | Apply a thin and even layer. Use: 8637076, Activator
Allow to dry for at least 10 minutes. |
| | IMG-373929 |
|
| | Apply a thin and even layer. Use: 8637076, Activator
Allow to dry for at least 10 minutes. |
| | |
| | IMG-373342 |
|
| | Disconnect the connector. |
| | IMG-373343 |
|
| | |
| | IMG-373340 |
|
| | |
| | IMG-372237 |
|
| | |
| | IMG-373346 |
|
| | |
| | IMG-358146 |
|
| | |
| | |
| | IMG-358137 |
|
| | Install component that comes with the accessory kit. |
| | IMG-358177 |
|
| | Caution! Make sure that the rubber grommet seals properly to the body. |
|
| | |
| | IMG-373355 |
|
| | |
| | IMG-372237 |
|
| | |
| | IMG-373358 |
|
| | |
| | IMG-373343 |
|
| | |
| | IMG-373357 |
|
| | |
| | IMG-373386 |
|
| | |
| | |
| | IMG-355927 |
|
| | |
| | IMG-355932 |
|
| | |
| | IMG-372962 |
|
| | |
| | IMG-372961 |
|
| | |
| | IMG-368833 |
|
| | |
| | IMG-360944 |
|
| | Repeat on the other side. |
| | IMG-360951 |
|
| | |
| | IMG-355945 |
|
| | |
| | IMG-355946 |
|
| | |
| | IMG-356006 |
|
| | |
| | IMG-373665 |
|
| | |
| | IMG-373664 |
|
| | Disconnect the connector, if applicable. |
| | IMG-355942 |
|
| | |
| | IMG-356008 |
|
| | |
| | IMG-356009 |
|
| | Disconnect the connector, if applicable. |
| | IMG-356007 |
|
| | |
| | IMG-373178 |
|
| | |
| | IMG-373168 |
|
| | |
| | IMG-358046 |
|
| | |
| | |
| | IMG-358053 |
|
| | |
| | IMG-373391 |
|
| | Pull the wiring through. Connect the connector. |
| | IMG-373393 |
|
| | |
| | IMG-372413 |
|
| | Locate the pre-routed connector. Remove the tape. |
| | IMG-372415 |
|
| | |
| | IMG-359181 |
|
| | Note! Prepare and install one holder at a time. |
|
| | IMG-373924 |
|
| | Note! Ensure that the tape is fixed to the surface. |
Remove the protective film. |
| | IMG-373925 |
|
| | Note! Ensure that the tape is fixed to the surface. |
Remove the protective film. |
| | IMG-373932 |
|
| | Clean the surfaces. Use: 1161721, Isopropanol
|
| | IMG-373934 |
|
| | Clean the surfaces. Use: 1161721, Isopropanol
|
| | IMG-373931 |
|
| | Warning! Make sure to provide adequate ventilation. |
Warning! Wear protective gloves. |
Apply a thin and even layer. Use special tool: T9512950, Glue gun (kit)
Use: 9511027, Glue
Use: 1161730, Mixing pipe
|
| | IMG-373930 |
|
| | Warning! Make sure to provide adequate ventilation. |
Warning! Wear protective gloves. |
Apply a thin and even layer. Use special tool: T9512950, Glue gun (kit)
Use: 9511027, Glue
Use: 1161730, Mixing pipe
|
| | IMG-373964 |
|
| | |
| | IMG-373965 |
|
| | |
| | IMG-372315 |
|
| | |
| | IMG-372304 |
|
| | Note! Apply pressure only where the tape is located. |
|
| | IMG-372303 |
|
| | Note! Hold the part securely at the marker arrows when removing the tool. |
|
| | IMG-373962 |
|
| | Install component that comes with the accessory kit. |
| | IMG-373963 |
|
| | Install component that comes with the accessory kit. |
| | IMG-373967 |
|
| | Put the wiring in the Bumper cover without installing the wiring. |
| | IMG-373743 |
|
| | Connect the two painted sensors to the external connections. |
| | IMG-373971 |
|
| | Repeat on the other side. |
| | IMG-373972 |
|
| | Repeat on the other side. |
| | IMG-373974 |
|
| | Note! Do not yet tighten the clamps. |
|
| | IMG-373980 |
|
| | Note! Do not yet tighten the clamps. |
|
| | IMG-373981 |
|
| | Adjust the position of the wiring harness. Tighten the cable ties. |
| | IMG-373998 |
|
| | |
| | |
| | IMG-372231 |
|
| | Place the Bumper Cover in position for installation. Connect the connectors. |
| | IMG-358175 |
|
| | |
| | Reinstall the removed parts in reverse order. |
| | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. Order and download software according to: 31330851
|