安装说明

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC90 2012
XC90 (03-) 2012

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
307890501.130664826, 30664415
Steering wheel, sport




M6400663




 
Equipment
A0000162
A0000161

M8802509

M8802108

D8802049

R8802817

M6400691

IMG-213320


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Preparations

1
A8800136
 

Preparations

  • Turn the ignition key to position 0. Remove the ignition key from the ignition switch.

  • Disconnect the battery negative lead.


Note!

Wait at least three minutes before unplugging the connectors or removing other electrical equipment.


 

Removing the 3-spoke steering wheel

2
M6400668
 

Removing the 3-spoke steering wheel

  • Reinsert the ignition key and turn it to position "I" to prevent the steering lock from engaging.

  • Turn the steering wheel a quarter turn so that the holes on the reverse of the steering wheel are accessible.

3
M6400670
 

  • Insert a screwdriver in the hole (2) on the reverse side of the steering wheel at right angles to the rear surface.

    Insert the screwdriver as far as possible to locate the end of the locking spring (1).

  • Position the end of the screwdriver on the top of the spring clip as illustrated

  • Pry the screwdriver upwards towards the upper edge of the hole (2) so that the end of the screwdriver presses the spring clip down (1) until one side of the steering wheel module springs out and releases from the mounting

  • Turn the steering wheel a half turn in the opposite direction. Carry out the same operation on the other side

  • Turn the steering wheel to a neutral position.

4
M3903271
 

  • Fold the steering wheel module out

  • Remove the two connectors (1) for the ignition cables for the airbag. First press in the catches on the sides. Then pull the connectors straight out.


    Note!

    The connectors are tightly secured. However, tools must not be used when removing.


  • Place the steering wheel module to one side.

5
M6400685
 

    Remove:

  • the connector (1)

  • the screw (2) that holds the steering wheel, leave the steering wheel in place.

6
M6400686
 

    Remove:

  • the screw (1). Install the screw in the contact reel (2).

  • the steering wheel. Pull the wiring out through the hole in the steering wheel.

 

7
M6400687
 

  • Remove the screw (1) and detach the ground lead.

    Applies to cars without RTI keypad mounted to the steering wheel

  • Remove the three screws (2) and lift out the horn ring (3).

  • Place the steering wheel to one side.

    Applies to cars with RTI keypad mounted to the steering wheel

  • Remove the three screws (2) and detach the horn ring (3).

8
M6400688
 

Applies to cars with RTI keypad mounted to the steering wheel

  • Carefully rotate the horn ring upwards and position it as illustrated.

  • Remove the connector for the RTI keypad mounted to the steering wheel. Press in the catch (1) and pull out the connector.

  • Place the horn ring to one side.

9
M6400689
 

Applies to cars with RTI keypad mounted to the steering wheel

    Remove:

  • the two screws in the bracket for the RTI keypad

  • the bracket and press the keypad out from the steering column cover.

  • Place the steering wheel to one side.

10
M6400676
 

Applies to cars with vibration damper

  • Remove the screw (2) and the vibration damper (1).

  • Place the steering wheel to one side.

 

Removing the 4-spoke steering wheel

11
D8501891
 

Removing the 4-spoke steering wheel

  • Reinsert the ignition key and turn it to position "I" to prevent the steering lock from engaging.

  • Detach both spring-loaded screws (1) on the reverse side of the steering wheel with a Torx T30 screwdriver.

  • Unscrew the screws until they release from the threads and spring back.

  • Fold out the steering wheel module (2).


    Note!

    Handle the cables with care.


12
M8802904
 

    Remove:

  • the connector (1) for the horn.

  • the SRS connectors (2). Press in the catches on the sides and carefully pull the connectors straight back.


    Note!

    Although the connectors are tightly secured, do not use any tools when removing.


  • the steering wheel module. Place the steering wheel module safely with the front side facing upwards.

  • the bolt (3), but leave the steering wheel in place.

  • the vibration damper (4), if applicable.

  • the connector for the RTI keypad, if applicable.

13
M8802905
 

    Remove:

  • the screw (1). Install the screw in the contact reel (2).

  • the steering wheel. Pull the wiring out of the hole (3).

 

Installing the new steering wheel

14
 

Installing the new steering wheel

  • Install the new steering wheel.

    Applies to cars with vibration damper

  • Install the vibration damper in the new steering wheel and secure it with the screw, see step .


    Note!

    Make sure the screw is properly tightened and that the vibration damper is secure. The screw is self-tapping, which can make it difficult to tighten.


15A
M3903760
15B
M3903761
 

Applies to cars with RTI keypad mounted to the steering wheel when installing in a wooden steering wheel

    Illustration A

  • Place the steering wheel in a suitable position and cut along the existing marks with a small knife.


Note!

When cutting, make sure to hold the knife so that the cuts are perpendicular to the reverse side of the steering wheel. This will reduce the risk of cutting a hole that is too large since the edge around the keypad is only a few millimetres larger than the keypad itself.


Illustration B

  • Cut away some of the material on the reverse side of the steering wheel spoke.

  • Test and cut until the keypad fits properly.

16
M3903762
 

    Applies to cars with RTI keypad mounted to the steering wheel when installing in a wooden steering wheel

  • Install the keypad, two screws and clamp. Make sure the cable is positioned on the underside of the steering wheel spoke.

  • Insert the keypad into the hole in the steering wheel with the text on the buttons facing out. Press until it connects securely against the steering column cover.

17
M3903757
 

    Applies to cars with RTI keypad mounted to the steering wheel when installing in a wooden steering wheel

  • Install the screws and attach the keypad with the clamp around the steering wheel spoke.

18
M3903758
 

    Applies to cars with RTI keypad mounted to the steering wheel

  • Position the horn ring as illustrated.

  • Plug in the keypad connector to the terminal on the reverse side of the keypad located on the right-hand side of the horn ring. The wire from the installed keypad is very short and it can be difficult to install the connector.

19
 

  • Reinstall the horn ring in the steering wheel, see steps - . Make sure that the three springs on the underside are correctly positioned. Check that the ground lead is not trapped.

  • Install the three screws in the horn ring and tighten crosswise them to 8 ± 2 Nm (6 ± 1.5 lbf.ft.).


    Note!

    The screws are self-tapping.


  • Reinstall the ground lead. Tighten.


    Note!

    Make sure the screw is properly tightened and that the ground lead is secure. The screw is self-tapping, which can make it difficult to tighten.


  • Check the function of the horn by pressing the horn around its entire circumference. A metallic noise should be heard when the three contact points come into contact

20
M6400690
 

  • Insert the wiring through the hole in the new steering wheel. Insert the airbag ignition cables through the holder (1).

  • Carefully install the new steering wheel by holding it straight and aligning the locating pins (2) on the contact reel.

  • Remove the screw from the contact reel and reinstall the screw in the holder. See step .

  • Install the new screw (3). Tighten to 40 Nm (30 lbf.ft.).

  • Plug in the connector (4).

21
M6400669
 

  • Check that the two springs (1) are in position

  • Press the two connectors for the ignition cables for the airbag into the steering wheel module

  • Insert the two pins on the reverse of the steering wheel module in the two springs. Ensure that the ignition cables are not trapped

  • Press the steering wheel module firmly into its mountings. (Two clearly audible clicks should be heard)

 

Supplementary work

22
A8800137
 

Supplementary work

  • Turn the ignition key to position II.

  • Reconnect the battery negative lead.