2014 L.H.D

Montaj Talimatları

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
S60 2014
S60 (11-18) 2014 B4164T, S60 (11-18) 2014 B4164T2, S60 (11-18) 2014 B4164T3

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313994981.031269364
Electric engine heater, 230V




IMG-378205




Equipment
A0000162
IMG-239660
IMG-239664

IMG-347561

IMG-378047


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 
1
IMG-363036
 

Color symbols


Note!

This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.


  1. Used for focused part, the part that you are to do something with.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

2
IMG-316263
 

Removal

 
3
IMG-342358
 

4
IMG-342359
 

5
IMG-342357
 

6
IMG-342360
 

7
IMG-378206
 

  • Use isopropanol to clean the bumper shell where the cutting template for the front engine block heater socket is to be secured.

  • Wipe dry.

8
IMG-378210
 

  • Use the template from the installation instructions.

  • Cut out following the dotted lines.

9
IMG-378213
 

  • Apply the template edge to edge with the line at the front edge of the front wheel arch and lower edge of the bumper cover.

10
IMG-378214
 

Accessory installation

  • Take a sharp knife. First make a thin cut along the edges of the inside of the template. This provides a groove to follow. Then cut carefully out of the bumper cover.


Note!

Cut carefully. It is easy to slip with the knife and move outside the template.


  • Remove the template and tape pieces.

  • Install the protective cover for the front engine block heater socket from the kit. Check that it aligns. Adjust the hole using a knife or file as necessary.

  • Smooth off the hole edges. Remove any swarf.

11
IMG-347226
 

  • Press the protective cover (from the kit) into place in the hole cut in the bumper cover.

  • Take the cable for the front engine block heater socket with ground lead from the kit and thread them through the protective cover.

12
IMG-347586
 

  • Install the attaching brace and nut from the kit.

  • Plug the electrical connector into the front engine block heater socket. Use the connector as a counterhold when tightening.

  • Tighten the front engine block heater socket to the bumper shell.

13
IMG-342365
 

  • Ensure that the front intake cover opens rearwards.

14
IMG-340317
 

Removal

15
IMG-340576
 

16
IMG-341072
 

Accessory installation

  • Route the cable with ground lead from the front intake behind the subframe's left-hand front mounting.

17
IMG-342366
 

  • Continue downwards on the inside of the subframe.

18
IMG-347581
 

  • Drill a Ø4 mm (Ø5/32") hole for the front intake grounding on the underside of the left front side member as illustrated.

  • Deburr the hole edges, remove the drill swarf and apply rustproofing agent.

  • Take a screw and toothed washer from the kit. Tighten the ground cable.

19
IMG-347588
 

  • Clamp the cable from the front engine block heater socket at the left front mounting in the sub-frame in the hole for it.

 
20
IMG-279168
 

  • Drain the coolant.

  • Tighten the nipple after draining.

21
IMG-347237
 

  • Disconnect the hose.

22
IMG-347238
 

  • Slacken off the screw to the AC compressor a few turns.

23
IMG-347240
 

  • Cut the hose from the oil cooler.


Note!

Some coolant may run out.


24A
IMG-347241
24B
IMG-347242
 

  • Do not tighten the screw (K) fully yet.

  • Turn the heater approximately as illustrated.

25
IMG-347243
 

  • Install the heater with bracket in the screw for the AC unit.


Note!

The lug in the AC compressor for the heater bracket.



Note!

Do not tighten the hose clamps yet fully yet.


26
IMG-347244
 

  • Install the upper hose in the heater.


Note!

The lug in the AC compressor for the heater bracket.



Note!

Do not tighten the hose clamps yet fully yet.


27
IMG-347245
 

  • Connect the hose from the oil cooler.

  • Ensure that the heater is in the clamp properly and the hoses are routed correctly.

  • Tighten all hose clips.

28
IMG-347246
 

29
IMG-347596
 

  • Lubricate the O-ring on the connector on the cable with low temperature grease.


Note!

Do not get any grease on the surfaces of the connector.


30
IMG-347248
 

  • Connect the cable to the heater.

31
IMG-347250
 

  • Take the clip from the kit and press onto the sub frame's upper/front edge and at the left front-edge of it.

32
IMG-344086
 

Applies when fitting passenger compartment connector at the same time

  • Take the locking sleeves and branching point from the kit.

  • Connect the cables in accordance with the following:

  • Cable (1) from the engine block heater.

    Cable (2) to the passenger compartment connector socket.

    Cable (3) from the front engine block heater socket.

  • Press the cables firmly into the junction connector and press the locking sleeves in over the cable splices.

33
IMG-347596
 

  • Lubricate the O-ring on the connector on the cable with low temperature grease.


Note!

Do not get any grease on the surfaces of the connector.


34
IMG-347251
 

Applies when only the engine block heater is installed

  • Connect the cables and clamp in clips.

35
IMG-347252
 

Applies to all vehicles

  • Clamp the cables at the sub-frame's front edge/upper edge.

36
IMG-347253
 

  • Clamp the cable splice at the existing cable harness.

37
IMG-317784
 

Installation

  • Fill with coolant, run the engine to operating temperature, bleed the cooling system and check that there are no leaks.

  • Post-fill the cooling system if necessary.

  • Reinstall the detached components in reverse order.

38
 

  • Reinstall the detached components in reverse order.