| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | IMG-426135 |
|
| | Set the vehicle to Inactive mode. |
| | IMG-466725 |
|
| | |
| | IMG-404645 |
|
| | |
| | IMG-404650 |
|
| | |
| | IMG-404655 |
|
| | |
| | IMG-420663 |
|
| | Remove the clips. Remove the screws. |
| | IMG-412725 |
|
| | |
| | IMG-392033 |
|
| | |
| | IMG-391976 |
|
| | Note! Close the drain cock after the coolant has drained. |
Place a container under the car. Drain the coolant. |
| | IMG-466723 |
|
| | |
| | IMG-403425 |
|
| | Remove the marked part. Use: Pliers
|
| | IMG-415975 |
|
| | Remove the screws. Remove the marked part. |
| | IMG-466897 |
|
| | Remove the screws. Remove the clips. |
| | IMG-448299 |
|
| | |
| | IMG-421164 |
|
| | |
| | IMG-421165 |
|
| | Remove the nut. Remove the clip. |
| | IMG-421166 |
|
| | |
| | IMG-448503 |
|
| | Remove the cable harness clips. |
| | IMG-448504 |
|
| | Loosen the screws. Remove the marked part. |
| | IMG-448505 |
|
| | Caution! Take extra care when handling the component. |
Fold marked part aside. |
| | IMG-448507 |
|
| | Remove the screws. Remove the marked part. |
| | IMG-472952 |
|
| | |
| | IMG-473297 |
|
| | |
| | IMG-473386 |
|
| | |
| | |
| | IMG-473387 |
|
| | Install component that comes with the accessory kit. Check that the flange of the part is in full contact with bumper cover. Adjust the hole with a file or knife as necessary. |
| | IMG-472974 |
|
| | |
| | IMG-472979 |
|
| | |
| | IMG-473011 |
|
| | Note! Do not fully tighten the nut yet. |
Assemble components that come with the accessory kit. |
| | IMG-473069 |
|
| | Install component that comes with the accessory kit. This is used as a counterhold. |
| | IMG-473080 |
|
| | Tighten the nut. Use hands only. |
| | IMG-449636 |
|
| | |
| | IMG-466585 |
|
| | Release the catches. Loosen the marked detail. |
| | IMG-466592 |
|
| | Loosen the nut. The item is to be reused. |
| | IMG-466614 |
|
| | Connect the prerouted cable. |
| | IMG-466619 |
|
| | Install the marked component. Ensure that all clips engage. |
| | IMG-466528 |
|
| | Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-448506 |
|
| | Reinstall the removed part. Reinstall the screws. |
| | IMG-448509 |
|
| | Reinstall the removed part. |
| | IMG-448504 |
|
| | Reinstall the removed part. Reinstall the screws. |
| | IMG-412700 |
|
| | Connect the connectors. Install the catch. |
| | IMG-412705 |
|
| | Install the clip(s). Tighten the cable tie. |
| | IMG-419071 |
|
| | |
| | IMG-391395 |
|
| | Caution! Cut carefully to avoid unintentional damage or personal injury. |
|
| | IMG-391422 |
|
| | |
| | IMG-391908 |
|
| | Tighten the screw. Tightening torque: M6
, 10 Nm
|
| | IMG-391906 |
|
| | Remove the screw. The part is to be reused. |
| | IMG-391910 |
|
| | Fold marked part aside. Install component that comes with the accessory kit. Tighten the screw.
|
| | IMG-391420 |
|
| | Install component that comes with the accessory kit. Tighten the hose clamps. |
| | IMG-391915 |
|
| | Caution! No grease on contact surfaces. |
Lubricate the O-ring. |
| | IMG-391913 |
|
| | Connect the cable. Install the catch. |
| | |
| | IMG-404661 |
|
| | Note! Always follow the manufacturer's instructions when handling the equipment. |
Use special tool: T9512955, Cover
Use special tool: T9512957, Coolant Reservoir
Fill with coolant and run the engine to operating temperature. |
| | Reinstall the removed parts in reverse order. |
| | IMG-405228 |
|
| | Tightening torque: Aluminum wheel rim to wheel hub Stage 1:
4 Nm Stage 2:
50 Nm Stage 3:
140 Nm
|