• Clean the sensors. Use: Isopropanol

• Allow to dry.

• Carefully mat down the surface. Use Glasspaper, grade P1000.

• Clean the sensors again. Use: Isopropanol

• Allow to dry.

• Avoid contact with the cleaned surfaces.

• Paint the sensors in the same colour code as the vehicle.

• Use Volvo Touch-up paint. (Only use base coat.)

• Use: Volvo 2-K Varnish. P/N: 31335447

• Set the ignition key to position 0.

• Fold back the mat.

1. Remove the cable harness clips.

2. Unplug the connector.

Applies to vehicles with Four-C (Active chassis)

Applies to all models

Applies to cars with an automatic transmission

• Release the shift-lock function.

Applies to all models

• Reinstall the detached components in reverse order.

• Remove the side cushion by first pulling it backwards at the upper edge until the hook (1) releases. Then pull the side cushion inwards slightly until the hook (2) releases, and upwards until the locating pin (3) disengages from the mounting at the rear edge.

• Detach the C-pillar panel at the lower edge by prying out the lower edge until the two clips release. Angle out the lower edge of the panels and then unhook the upper edge.

• Remove the headlining panel by first pulling the rear edge downward so that the four clips release. Then unhook the front edge.

• Remove the smaller headlining panel by pulling it laterally so that the two hooks release. Then unhook the front edge of the panel.

• Use: 9995919 Hook. Insert into the holes on the upper edge of the cover. Turn the tool and pull off the cover.

• Remove the loading eyelet screws. Tightening torque M8 screws: 24 Nm (17.7 lbf.ft).

• Slacken off the two screws in the sill panel.

• Remove the sill panel by pulling it straight up so that the six clips release.

• Remove the screw.

• Remove the side panel by detaching and angling out the upper edge.

• Also carried out on the other side.

• The cable harness will not be used again.

• Locate the two markings at the upper edge of the bumper cover.

1. Ø 3 mm (7/64")

2. Ø 10 mm (25/64")

• Use: 9997234 Hole tool

• Locate the two markings at the lower edge of the bumper cover.

• Mark the centre, use a scriber.

• Extend the marking's vertical line using a scriber. This is to be used as a reference line for punching holes.

Illustration A

1. Ø 3 mm (7/64")

2. Ø 10 mm (25/64")

Illustration B

• Use: 9997367 Hole tool

• Ensure that the markings, 1 and 2, are opposite each other when making holes.

Applies to the left-hand side

• Ensure that the marking on the hole tool (LH) and the marking that was made on the bumper cover are opposite each other.

Applies to the right-hand side

• Ensure that the marking on the hole tool (RH) and the marking that was made on the bumper cover are opposite each other.

• Clean the inside of the bumper cover using a mild soap solution.

• Clean an area around the holes that is slightly larger than the sensor holder. Use isopropanol. Allow to dry.

• Clean using isopropanol.

• Clean using isopropanol.

• Apply a thin and even layer of activator. Allow to dry for at least 10 minutes.

• Use: 8637076 Activator.

• Apply a thin and even layer of activator. Allow to dry for at least 10 minutes.

• Use: 8637076 Activator.

• Locate the taped connector and connect it to the control module.

• The cable harness will not be used again.

• Apply two pieces of tape.

• Remove the protective film from the tape.

• Apply a thin and even layer of adhesive. The adhesive must be above the tape level.

• Use: 9512950 Adhesive gun, 1161730 Mixing pipe and 9511027 Adhesive.

• Press the holder towards the casing, but only at the places where there is tape.

• Hold the cradle securely when removing the centering tool.

• Repeat the method steps on the other cradle.

• Apply two pieces of tape.

• Remove the protective film from the tape.

• Apply a thin and even layer of adhesive. The adhesive must be above the tape level.

• Use: 9512950 Adhesive gun, 1161730 Mixing pipe and 9511027 Adhesive.

• Repeat the method steps on the other cradle.

• Reinstall the detached components in reverse order.

• Download the software for the accessory's function following the service information in VIDA.