Preparations

Preparations

• Clean the sensors. Use: Isopropanol.

• Allow to dry.

• Carefully mat down the surface. Use Glasspaper, grade P1000.

• Clean the sensors again. Use: Isopropanol

• Allow to dry

• Avoid contact with the cleaned surfaces.

• Paint the sensors in the same colour code as the vehicle.

• Use Volvo Touch-up paint. (Only use base coat.)

• Use: Volvo 2-K Varnish. P/N: 31335447

• Turn the ignition switch to position 0.

  
  

  Note! Wait at least one minute before unplugging the connectors or removing other electrical equipment.

  
  

• Remove the four screws holding the end of the rear bumper.

  Repeat the operation on the other side.

• Remove the two nuts at the lower edge of the bumper cover.

• Pull the corner straight out, continue to pull the bumper cover backwards until the five clips at the upper edge release.

  Repeat the operation on the other side.

• Open the boot lid/tailgate.

• Remove the bumper cover by pulling it backwards until the three catches opposite the tailgate opening have released.

• Locate the 4 markings on the inside of the bumper cover.

• Mark center with a scribe.

• Drill out the markings using a Ø 3 mm (1/8") diameter drill bit.

• Drill out the holes. Use a Ø10 mm (13/32") diameter drill bit.

• Use special tool: 9997234 Hole tool.

• Clean around the holes and the markings. Use: Isopropanol.

• Take four holders from the kit.

• Clean the cradles on the surface as illustrated. Use: Isopropanol.

• Allow to dry.

• Apply a thin and even layer of activator to the cleaned surfaces where the tape is to be attached. Use: 8637076 Activator.

• Allow to dry for at least 10 minutes.

• Apply a thin and even layer of activator to the cleaned surfaces where the tape is to be attached. Use: 8637076 Activator

• Allow to dry for at least 10 minutes.

• Lift out the cargo compartment carpet.

• Remove the sill trim panel by first pulling it forward until the clips in the front edge release. Then pull it upward until the clips in the top edge release.

• Fold forward the right backrest in the backseat.

Remove:

• the clips

• the plastic nuts

• the connector to the cargo compartment lighting

• the side panel.

Unplug connector for 12V outlet, if installed.

Installation of the Parking Assistance Module (PAM)

Installation of the Parking Assistance Module (PAM)

• Locate the two studs positioned on the right-hand side underneath the tail lamp in the cargo compartment. Press the control module's holder on the studs.

• Press the control module on the holder.

• Remove the rubber seal.

• Remove the support under the left-hand tail lamp by removing the two screws.

• Take the short cable harness and thread the end with the black connector through the hole in the body.

• Install the rubber grommet.

• Reinstall the support under the left-hand tail lamp.

• Hook the connector onto the rail.

• Connect the newly routed cable harness to the control module.

• Locate the light brown connector. It originates from the same cable harness as the connector for cargo compartment lighting.

• Connect the connector to the control module.

Reinstall:

• the side panels.

• the sill trim panel.

• the floor carpet.

• Fold up the backrest.

Installing sensors

Installing sensors

• Check which holder is to be positioned where before installing. The two middle holders are the same whilst the two outer holders are specific.

• Apply two pieces of tape to each holder.

• Remove the protective film from the tape.

• Apply a thin layer and even layer of adhesive.

  
  

  Note! The adhesive must be above the level for the tape.

  
  
  

  Caution! The adhesive must not come into contact with the tape.

  
  

• Use special tool: 9512950 Adhesive gun

• Use: 1161730 Mixing pipe

• Use: 9511027 Adhesive.

• Install the centering tool in one holder.

• Install the tool on the bumper cover.

• Hold the holder securely when removing the centering tool. The holder must be installed horizontally and in line with the bumper cover.

• Repeat the steps until all four holders are in place.

• Connect the cable harness connectors to the sensors.

• Install the sensors in their holders. Take care not to release the holders from the tape when installing.

  
  

  Note! The large gray connector must protrude from the right-hand side of the bumper cover (see image 31).

  
  

• Press the six cable holders on the longitudinal flange of the bumper casing.

Installing the bumper

• Lift up the bumper and connect the connector.

• Press the bumper's hooks in at the rear edge. Press all the hooks for the ends into the body.

• Reinstall the screws on the front edges of the bumper casing.

• Reinstall the plastic nuts at the lower edge.

Installing the switch

Installing the switch

• Press the panel in at the front edge.

• Lift the panel at the rear edge and remove it.

• Remove the cover.

• Install the new switch. It must be fitted in the first available button location seen from the steering wheel.

  
  

  Note! Cover plugs are purchased separately.

  
  

• Reinstall the gear selector panel.

• Download software (application) for the accessory's function according to service information in VIDA. See VIDA or accessories catalogue for article number on software.