2015 R.H.D

Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC70 2015
XC70 (08-) 2015 R.H.D

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
314145481.031339994
Parking assistance camera wide angle front (2013w46-)




IMG-376581




Special tools

 

951 2932 Tension spring

Tool number:951 2932

Tool description:Tension spring

Tool boards:80


Materials

Designation

Part number

Low temperature grease

1161427


Equipment
IMG-242205
IMG-345497
IMG-300203
IMG-327738
IMG-239667
IMG-244945

IMG-380836


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Conditions

2
IMG-332179
 

Set the ignition key to position 0.

Remove the battery's negative cable.

 

Color symbols

3
IMG-363036
 

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

  1. Used for focused component, the component with which you will do something.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

 

Removal

4
IMG-376333
 

Remove the panel.

5
IMG-376334
 

Remove the weatherstrip.

6
IMG-376348
 

Remove the panel.

7
IMG-376350
 

Remove the panel.

8
IMG-376352
 
9
IMG-354320
 
10
IMG-349804
 

Remove the panel.

11
IMG-349806
 

Remove the screws.

12
IMG-345282
 

Remove the screws.

 

Cars with manual transmissions

13
IMG-345747
 

Release the catch which is located inside the gear lever boot.

14
IMG-347222
 
 

Cars with automatic transmissions

15
IMG-345283
 
16
IMG-345284
 

Release the shift-lock function.

17
IMG-341878
 

Remove the panel.

18
IMG-346036
 

Remove the panel.

19
IMG-340599
 
  1. Fold the carpet to the side.

  2. Unhook the clip(s).

  3. Disconnect the connector.

20
IMG-353601
 
21
IMG-353602
 

Remove the screws.

22
IMG-347139
 

Remove the panel.

 

Vehicles with the 4C system.

23
IMG-345317
 

Disconnect the connector.

 

All vehicles

24
IMG-376353
 

Caution!
Be careful not to damage the catches.

Remove the panel.

25
IMG-340605
 

Remove the screws.

26
IMG-345296
 
27
IMG-380815
 
 

Accessory installation

28
IMG-380819
 
29
IMG-380815
 
 

Removal

30
IMG-349942
 

Remove the screws.

31
IMG-349946
 
32
IMG-353492
 

Disconnect the connectors.

33
IMG-349876
 

Remove the panel.

34
IMG-349877
 

Remove the screws.

Remove the panel.

35
IMG-349901
 

Caution!
The number of connectors can vary depending on the vehicle's equipment level.

Disconnect the connectors.

36
IMG-349903
 
37
IMG-353512
 
38
IMG-353511
 

Remove the screws.

39
IMG-349993
 

Remove the panel.

40
IMG-350006
 

Remove the panel.

41
IMG-352301
 

Remove the screws.

On both sides.

42
IMG-352271
 

Remove the panel.

43
IMG-350026
 

Remove the screws.

44
IMG-349999
 

Detach the panel.

45
IMG-349992
 

Disconnect the connector.

 

Accessory installation

46
IMG-350072
 
47
IMG-355161
 

Caution!
Make sure that no part of the wiring harness is trapped.

Facilitate cable routing by temporarily raising the floor bracket using a socket or similar.

Pull the wiring through.

48
IMG-355174
 

Connect the connectors.

49
IMG-355175
 

Tear off the excess foam tape.

50
IMG-355200
 

Route the cable harness to the existing cable harness.

51
IMG-376366
 

Route the cable harness to the existing cable harness.

Install the cable.

Pull the wiring through.

52
IMG-376365
 
53
IMG-345863
 

Connect the connectors.

54
IMG-349904
 
 

Removal

55
IMG-340541
 

Fold the carpet to the side.

Locate the rubber grommet under the insulation and press it out.

 

Accessory installation

56
IMG-376368
 

Note!
Do not yet tighten the clamps.

Route the cable harness to the existing cable harness.

57
IMG-376369
 
 

Installation

58
IMG-353491
 

Connect the connectors.

59
IMG-349948
 
60
IMG-349942
 

Install the screws.

 

Removal

61
IMG-345877
 

Remove the clips.

Remove the screws.

62
IMG-345878
 
63
IMG-340542
 

Note!
On some markets the rubber grommet may be covered by the heat shield.

 

Accessory installation

64
IMG-345881
 
65
IMG-353681
 

Caution!
Take extra care when handling the component.

Pull the wiring through.

Use: 1161427, Low temperature grease

66
IMG-340954
 

Pull the wiring through.

 

Removal

67
IMG-353376
 
68
IMG-376394
 
69
IMG-353381
 

Disconnect the connector.

70
IMG-354328
 
71
IMG-273585
 
 

Accessory installation

72
IMG-340738
 


Use special tool: T9512932, Tension spring

73
IMG-340535
 

Caution!
Make sure to locate the wiring in such a way that any damage caused by heat or excessive wear is avoided.


Note!
Do not yet tighten the clamps.

Route the cable harness to the existing cable harness.

74
IMG-340747
 

Note!
Do not yet tighten the clamps.

75
IMG-376395
 

Note!
Do not yet tighten the clamps.

Route the cable harness to the existing cable harness.

76
IMG-376423
 

Caution!
Make sure to locate the wiring in such a way that any damage caused by heat or excessive wear is avoided.


Caution!
Tighten clamps properly.

77
IMG-376653
 

Caution!
Make sure to locate the wiring in such a way that any damage caused by heat or excessive wear is avoided.

Insert the cable in to the passenger compartment, adjust the cable length out into the engine compartment and secure the rubber grommet.

78
IMG-347781
 
79
IMG-347786
 
80
IMG-376589
 
81
IMG-376680
 
82
IMG-376597
 

Install the screws.

83
IMG-376613
 

Connect the connector.

84
IMG-336901
 

Reinstall the removed parts in reverse order.

Reinstall the battery's negative cable.

85
IMG-242268
 

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31288598