2015 R.H.D

Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC70 2015
XC70 (08-) 2015

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313734731.031373087
Parking assistance, rear




Special tools

 

999 5919 PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Tool number:999 5919

Tool description:PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Tool boards:46

 

999 7234 Hole stamp

Tool number:999 7234

Tool description:Hole stamp

Tool boards:80

 

951 2950 Glue gun (kit)

Tool number:951 2950

Tool description:Glue gun (kit)

Tool boards:08


Materials

Designation

Part number

Isopropanol

1161721

Sand paper P1000

Volvo Original Touch-up paint

Varnish 2-component

31335447

Activator

8637076

Glue

9511027

Mixing pipe

1161730


Equipment
IMG-242205
IMG-345497

IMG-377192

IMG-377249


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Further information

2
 

After installation, the car must not be washed for 48 hours

When installing, the car must retain a temperature of 20 degrees C.

 

Color symbols

3
IMG-363036
 

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

  1. Used for focused component, the component with which you will do something.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

 

Paintwork

4
IMG-373951
 
5
IMG-344142
 

Clean the surface.

Use: 1161721, Isopropanol

6
IMG-344141
 

Matt the surface gently.

Use: , Sand paper P1000

7
IMG-344142
 

Clean the surface.

Use: 1161721, Isopropanol

8
IMG-377210
 

Caution!
Protect connector surfaces against paint spray.

Use: , Volvo Original Touch-up paint

Use paint colours according to the colour code given in the image.

Use base coat only.

Use: 31335447, Varnish 2-component

Also see the instructions on the container.

9
IMG-333934
 

Caution!
First the paint must dry after painting.

 

Removal

10
IMG-332193
 

Set the ignition key to position 0.

11
IMG-377098
 

Note!
Orientation view

12
IMG-372212
 

Measure and mark as illustrated.

13
IMG-372210
 
14
IMG-372209
 


Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

15
IMG-372207
 
 

Accessory installation

16
IMG-372208
 
 

Removal

17
IMG-259683
 

Remove the screws.

18
IMG-259684
 

Remove the nuts.

19
IMG-259754
 

Remove the screws.

Repeat on the other side.

20
IMG-259756
 

Caution!
Place the Bumper Cover on a suitable surface.

 

Accessory installation

21
IMG-283030
 

Locate the markings for the positions.

Mark the centre.

22
IMG-283031
 
23
IMG-273313
 

Caution!
Sharp end of tool must be on outside of cover.


Use special tool: T9997234, Hole stamp

24
IMG-283032
 

Clean the surfaces.

Use: 1161721, Isopropanol

25
IMG-377226
 

Clean the surface.

Use: 1161721, Isopropanol

26
IMG-283033
 

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

27
IMG-283028
 

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

 

Removal

28
IMG-261414
 
29
IMG-273316
 
 

Accessory installation

30
IMG-273317
 
31
IMG-273318
 
32
IMG-273319
 

Locate the pre-routed connector.

33
IMG-273320
 

The part is not to be reused.

34
IMG-273321
 

Caution!
Make sure that the rubber grommet seals properly to the body.

Install component that comes with the accessory kit.

35
IMG-273322
 
36
IMG-273323
 

Connect the connectors.

37
IMG-273324
 
38
IMG-377228
 

Note!
Prepare and install one holder at a time.

39
IMG-377239
 

Note!
Ensure that the tape is fixed to the surface.

Remove the protective film.

40
IMG-377241
 

Warning!
Make sure to provide adequate ventilation.


Warning!
Wear protective gloves.

Apply a thin and even layer.

Use: 9511027, Glue


Use special tool: T9512950, Glue gun (kit)

Use: 1161730, Mixing pipe

41
IMG-297571
 
42
IMG-297572
 

Note!
Apply pressure only where the tape is located.

43
IMG-297573
 

Note!
Hold the part securely at the marker arrows when removing the tool.

44
IMG-377247
 

Put the wiring in the Bumper cover without installing the wiring.

45
IMG-247287
 
46
IMG-377248
 
47
IMG-273328
 

Caution!
Hold the newly bonded sensor holder in position whilst pressing the clip into position.

Install the cable.

 

Installation

48
IMG-273330
 

Request the aid of a colleague for this procedure.

Place the Bumper Cover in position for installation.

Connect the connector.

49
IMG-273331
 
50
IMG-377070
 

Reinstall the removed parts in reverse order.

51
IMG-242268
 

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 30765571