| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | IMG-400007 |
|
| | When installing, the car must retain a temperature of 20 degrees C. After installation, the car must not be washed for 48 hours |
| | |
| | IMG-363036 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | |
| | IMG-350367 |
|
| | Caution! Observe caution, the glass breaks easily. |
Remove the glass from the mirror. |
| | IMG-350369 |
|
| | Disconnect the connectors. |
| | IMG-350368 |
|
| | |
| | IMG-359036 |
|
| | |
| | IMG-350370 |
|
| | |
| | |
| | IMG-418627 |
|
| | Install component that comes with the accessory kit. |
| | IMG-359046 |
|
| | |
| | IMG-359048 |
|
| | |
| | IMG-359047 |
|
| | |
| | Repeat all method steps for the other side. Reinstall the removed parts in reverse order. |
| | |
| | IMG-416246 |
|
| | Remove the marked part. The part is not to be reused. Use: Interior trim remover
|
| | IMG-416247 |
|
| | Remove the marked part. The part is not to be reused. Use: Interior trim remover
|
| | |
| | IMG-416245 |
|
| | Install component that comes with the accessory kit. Use: Interior trim remover
|
| | IMG-416241 |
|
| | Install component that comes with the accessory kit. Use: Interior trim remover
|
| | IMG-416242 |
|
| | Install component that comes with the accessory kit. Use: Interior trim remover
|
| | IMG-416251 |
|
| | Place the component where indicated in the graphic. |
| | IMG-416252 |
|
| | |
| | When installing on right-hand drive cars, perform the procedures on the opposite side and/or mirrored. |
| | |
| | IMG-414897 |
|
| | Remove the part carefully |
| | IMG-414896 |
|
| | Clean the surface. Wipe dry. |
| | |
| | IMG-414902 |
|
| | Measure and mark as illustrated. |
| | IMG-418630 |
|
| | Remove the protective film. Install component that comes with the accessory kit. |
| | IMG-414899 |
|
| | Note! Press and apply pressure to the part over the tape for at least 20 seconds. |
|
| | Repeat all method steps for the other side. |
| | |
| | IMG-352899 |
|
| | Remove the part carefully |
| | IMG-352929 |
|
| | |
| | IMG-367797 |
|
| | |
| | IMG-367741 |
|
| | Release the locks. Use: Electrician's screwdriver
|
| | IMG-367751 |
|
| | |
| | IMG-367755 |
|
| | |
| | |
| | IMG-418656 |
|
| | Install component that comes with the accessory kit. A click confirms that the component is in the correct position. |
| | IMG-367774 |
|
| | A click confirms that the component is in the correct position. |
| | Reinstall the removed parts in reverse order. |
| | |
| | IMG-411545 |
|
| | Clean the surfaces. Use: 1161721, Isopropanol
|
| | |
| | IMG-418640 |
|
| | Note! Make sure that the component is centred. |
Place the component where indicated in the graphic. Use appropriate tape to mark the position.
Use: , Masking tape
|
| | IMG-411447 |
|
| | Measure Use: Tape measure
Remove the marked part. |
| | IMG-411466 |
|
| | Fold the protective film forward |
| | IMG-411465 |
|
| | |
| | IMG-411531 |
|
| | Caution! Cut carefully to avoid unintentional damage or personal injury. |
Cut the component following the instructions in the graphic. |
| | IMG-411533 |
|
| | Apply the stated Material on the marked surface. Use: 8750060, Glue
|
| | IMG-411540 |
|
| | Note! Make sure that the component is clean and free of foreign material. |
Install component that comes with the accessory kit. Place the component where indicated in the graphic. |
| | IMG-411727 |
|
| | Remove the protective film. |
| | IMG-411735 |
|
| | Note! Press and apply pressure to the part over the tape for at least 20 seconds. |
|
| | IMG-411541 |
|
| | Remove the protective film. |
| | IMG-411542 |
|
| | Note! Press and apply pressure to the part over the tape for at least 20 seconds. |
|
| | Repeat the steps when installing accessories on opposite side. |
| | |
| | IMG-411543 |
|
| | |