Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
S80 2014
S80 (07-) 2014 B4204T7, S80 (07-) 2014 B4204T6

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313995231.131260693
Electric engine heater, 230V




IMG-378240




 
Equipment
A0000162
IMG-239664
IMG-239660
IMG-239980

IMG-331108

IMG-378072


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 
1
IMG-363036
 

Color symbols


Note!

This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.


  1. Used for focused part, the part that you are to do something with.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

2
IMG-316263
 

Removal

3
IMG-331109
 

4
IMG-331110
 

  • Undo the clamp for the intake hose and pull the hose off.

5
IMG-231547
 

6
IMG-231549
 

7
IMG-231550
 

8
IMG-231551
 

9
IMG-378244
 

  • Clean the area where the template is to be attached.


Note!

Use soap solution.


10
IMG-378259
 

  • Use the template from the installation instructions.

  • Cut out following the dotted lines.


Note!

Check the scale.


11
IMG-378251
 

  • Attach the template using tape edge to edge with the embossing to the front wing and the embossing in the bumper cover as illustrated.

12
IMG-378254
 

Accessory installation

  • Take a sharp knife. First make a thin cut along the edges of the inside of the template. This provides a groove to follow. Then cut carefully out of the bumper cover.


    Note!

    Cut carefully. It is easy to slip with the knife and move outside the template.


  • Remove the template.

  • Install the protective cover for the front engine block heater socket from the kit. Check that it aligns. Adjust the hole using a knife or file as necessary.

  • Smooth off the hole edges. Remove any swarf.

13
IMG-231564
 

  • Press the protective cover (from the kit) into place in the hole cut in the bumper cover.

  • Take the cable for the front engine block heater socket with ground lead from the kit and thread them through the protective cover.

14
IMG-231566
 

  • Install the attaching brace and nut from the kit.

  • Connect the electrical cable to the front intake. Use the connector as a counterhold when tightening.

  • Tighten the front engine block heater socket to the bumper shell.

  • Press the cable into the holder on the washer fluid reservoir.

  • Remove the cover on the radiator expansion tank.

15
IMG-231565
 

  • Ensure that the front intake cover opens rearwards.

16
IMG-231309
 

17
IMG-231567
 

  • Route the cable with ground lead from the front intake in front of the subframe's left-hand front mounting.

18
IMG-231568
 

  • Continue downwards on the inside of the subframe.

19
IMG-231571
 

  • Drill a Ø4 mm (Ø5/32") hole for the front intake grounding on the underside of the left front side member as illustrated.

  • Deburr the hole edges, remove the drill swarf and apply rustproofing agent.

  • Take a screw and toothed washer from the kit. Tighten the ground cable.

 
20
IMG-279168
 

  • Drain the coolant.

  • Tighten the nipple after draining.

21
IMG-331126
 

  • Pull the intake hose down and secure it at the sub frame.

22
IMG-331128
 

  • Take a spacer sleeve from the kit and tighten in the right-hand hole on the front side of the engine above the joint between the engine block and oil sump.

23
IMG-331133
 

  • Take the heater and clamp from the kit and assemble as illustrated.

24
IMG-331134
 

  • Take screws from the kit and tighten the heater in the spacer sleeve.

25
IMG-331135
 


Note!

Orientation view


26
IMG-331136
 

  • Cut the hose (1) as follows:

  • Measure out for cutting the coolant hose between the oil cooler and the thermostat housing.

    Position the hose at the heater's lower connection, ensure that it runs around the oil filter properly and cut it.

27
IMG-331137
 

  • Smooth off the hose ends if necessary. Do not cut off too much of the hoses.

  • Take hose clamps and tighten the hoses to the heater, preferably from underneath.

28
IMG-214134
 

  • Take the clip with cable tie for a Ø6.5 mm (Ø1/4 ") hole and press it into the left hole on the inside of the upper edge of the subframe.

29
IMG-331138
 

  • Take the two clips from the kit and press them onto the sub frame's upper/front edge and at the left front-edge of it.

  • Position the clip that is to be nearest the cable tie fitted previously according to the measurements specified in the image.

30
D3601932
 

  • Lubricate the O-ring on the connector on the cable from the front engine block heater socket with low temperature grease.


Note!

Do not get any grease on the surfaces of the connector.


31
IMG-214136
 

Applies when only the engine block heater is installed

  • Take the joint cable to the engine block heater from the kit and connect to the cable from the front engine block heater socket. Press the connectors together firmly and secure a locking sleeve from the kit over the cable splice.

32
IMG-331143
 

  • Clamp the cable splice (1) to the inside of the subframe using the cable tie and press the cable into the clips.

33
IMG-331148
 

Applies when fitting passenger compartment connector at the same time

  • If the passenger compartment connector is to be installed at the same time, install the junction connector now. Lubricate the O-rings on the contacts as previously.

  • Connect:

  • cable (1) from the front intake

    cable (2) to the passenger compartment connector socket

    cable (3) to the heater.

34
IMG-331153
 

  • Insert the junction connector into the space in the sub frame. Tighten the junction connector with the cable tie around the outer connector of the two on the junction connector. The position of the edge clip at the upper edge of the sub frame's left-hand side may need adjusting in order to fit the junction connector.

35
D3601932
 

Applies to all vehicles

  • Lubricate the O-ring on the connector on the jointing cable with low temperature grease.


Note!

Do not get any grease on the surfaces of the connector.


36
IMG-331158
 

  • Firmly secure the cable into the heater's connector.

  • Press in a locking sleeve from the kit over the cable splice.

37
IMG-331159
 

  • Move the intake hose up into place and tighten the clamp. Ensure that it ends up on the correct side of the cable to the heater.

38
IMG-331160
 

  • Clamp the cable splice around the intake hose using a double cable tie and edge clips with cable tie on the inside of the upper edge of the subframe.

39
IMG-231579
 

Installation

40
IMG-279192
 

41
IMG-279193
 

42
IMG-331163
 

43
IMG-317784
 

  • Fill with coolant and warm up the engine. Bleed the cooling system and check for leaks.

  • Top up the cooling system as required.

44
IMG-231335