| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
|  | | IMG-363036 |
|
| | Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | |
|  | | IMG-422428 |
|
| | |
| | Disconnecting the battery |
|  | | IMG-394535 |
|
| | |
|  | | IMG-425513 |
|
| | Remove the battery's negative cable.
Tightening torque: Battery cable for battery
, 6 Nm
|
| | |
|  | | IMG-382204 |
|
| | Remove the clips. Remove the screws. |
|  | | IMG-422562 |
|
| | |
|  | | IMG-422563 |
|
| | |
|  | | IMG-392033 |
|
| | |
|  | | IMG-391976 |
|
| | Note!
Close the drain cock after the coolant has drained. |
Place a container under the car. Drain the coolant. |
|  | | IMG-403425 |
|
| | Remove the marked part. Use: Pliers
|
|  | | IMG-415975 |
|
| | |
|  | | IMG-412692 |
|
| | Remove the clips. Remove the screws. |
|  | | IMG-412697 |
|
| | |
|  | | IMG-412710 |
|
| | Fold the wing liner aside. |
|  | | IMG-391565 |
|
| | |
|  | | IMG-391573 |
|
| | Release the catches. Fold marked part aside. |
|  | | IMG-391924 |
|
| | Remove the nut. The part is to be reused. |
|  | | IMG-412196 |
|
| | |
|  | | IMG-412198 |
|
| | |
|  | | IMG-412199 |
|
| | |
|  | | IMG-424701 |
|
| | |
| | |
|  | | IMG-424702 |
|
| | Measure and mark as illustrated. |
|  | | IMG-424703 |
|
| | |
|  | | IMG-424704 |
|
| | Adjust the hole with a file or knife as necessary. |
| | |
|  | | IMG-424705 |
|
| | Install component that comes with the accessory kit. |
|  | | IMG-412652 |
|
| | |
|  | | IMG-412230 |
|
| | |
|  | | IMG-424865 |
|
| | |
|  | | IMG-424870 |
|
| | Install component that comes with the accessory kit. Tighten the cable tie. |
|  | | IMG-392572 |
|
| | |
|  | | IMG-391930 |
|
| | |
|  | | IMG-422412 |
|
| | Connect the connectors. Install the catch. |
|  | | IMG-422413 |
|
| | Install the clip(s). Tighten the cable tie. |
|  | | IMG-419110 |
|
| | Install component that comes with the accessory kit. Tighten the cable tie. |
| | Vehicles with Power Pulse |
|  | | IMG-419071 |
|
| | Install component that comes with the accessory kit. Tighten the cable tie. |
| | |
|  | | IMG-425906 |
|
| | Hold the component in the position in which it is to be fitted and mark the hoses where they are to be cut. |
|  | | IMG-391395 |
|
| | Caution!
Cut carefully to avoid unintentional damage or personal injury. |
|
|  | | IMG-391422 |
|
| | |
|  | | IMG-391908 |
|
| | Tighten the screw.
Tightening torque: M6
, 10 Nm
|
|  | | IMG-391906 |
|
| | Remove the screw. The part is to be reused. |
|  | | IMG-391910 |
|
| | Fold marked part aside. Install component that comes with the accessory kit. Tighten the screw.
|
|  | | IMG-391420 |
|
| | Install component that comes with the accessory kit. Tighten the hose clamps. |
|  | | IMG-391915 |
|
| | Caution!
No grease on contact surfaces. |
Lubricate the O-ring. |
|  | | IMG-391913 |
|
| | Connect the connector. Install the catch. |
| | |
|  | | IMG-404661 |
|
| | Note!
Always follow the manufacturer's instructions when handling the equipment. |
Use special tool: T9512955, Cover
Use special tool: T9512957, Coolant Reservoir
Fill with coolant and run the engine to operating temperature. |
| | Reinstall the removed parts in reverse order. |
|  | | IMG-405228 |
|
| |
Tightening torque: Aluminum wheel rim to wheel hub
Stage 1:
4 Nm
Stage 2:
50 Nm
Stage 3:
140 Nm
|
