Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC70 2015
XC70 (08-) 2015 B4204T11

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
314143521.031359329
Electric engine heater, 230 V




IMG-380063




 

Materials

Designation

Part number

Grease

1161761


Equipment
IMG-345497
IMG-239664
IMG-239660
IMG-239980

IMG-380133

IMG-380582


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Conditions

2
 

When installing, the car must retain a temperature of 20 degrees C.

 

Color symbols

3
IMG-363036
 

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

  1. Used for focused component, the component with which you will do something.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

 

Removal

4
IMG-332193
 

Set the ignition key to position 0.

5
IMG-351277
 
6
IMG-380083
 
7
IMG-380084
 

Remove the screws.

8
IMG-380092
 

Remove the screws.

9
IMG-380086
 
10
IMG-380085
 

Disconnect the connector for the fog lamp.

Disconnect the connector.

11
IMG-380087
 

Remove the panel.

 

Accessory installation

12
IMG-380088
 

Caution!
Cut carefully to avoid unintentional damage or personal injury.

Locate relevant marking.

13
IMG-380090
 

Install the panel.

14
IMG-380089
 

Scribe/mark up

15
IMG-380087
 
16
IMG-380101
 

Caution!
Cut carefully to avoid unintentional damage or personal injury.

17
IMG-380090
 
18
IMG-381176
 
19
IMG-380613
 
20
IMG-363401
 
 

Removal

21
IMG-380093
 

Remove the screws.

22
IMG-358531
 
23
IMG-341914
 

Fold the wing liner aside.

 

Accessory installation

24
IMG-380094
 

Caution!
Ensure that the wire or wiring harness cannot rub against adjacent components.

25
IMG-380095
 
26
IMG-380107
 

Note!
Orientation view

27
IMG-380106
 
28
IMG-362914
 

Caution!
No grease on contact surfaces.

Lubricate the O-ring.

Use: 1161761, Grease

 

Vehicles with passenger compartment connector

29
IMG-380096
 
  1. Cable from front socket

  2. Passenger Compartment Connector Cable

  3. Cable from Engine block heater

30
IMG-380109
 
31
IMG-380111
 
 

Vehicles without passenger compartment connector

32
IMG-380654
 
  1. Cable from front socket

  2. Cable from Engine block heater

33
IMG-380662
 
 

All vehicles

34
IMG-381658
 

Attach any excess wire to the wiring harness.

35
IMG-380112
 
 

Removal

36
IMG-316303
 

Place a container under the car.

Drain the coolant.

37
IMG-380708
 
38
IMG-380929
 

Loosen the clip.

 

Accessory installation

39
IMG-380284
 
 

Installation

40
IMG-380928
 

Install the clip(s).

 

Removal

41
IMG-380706
 

Warning!
Be prepared to collect escaping fluid.

Loosen the clip.

Remove the hose.

42
IMG-380711
 

Remove the hose.

The part is not to be reused.

 

Accessory installation

43
IMG-380713
 

Install the hose.

Tighten the hose clamps.

44
IMG-381572
 
45
IMG-380720
 

Install the hose.

Tighten the hose clamp.

46
IMG-362914
 

Caution!
No grease on contact surfaces.

Lubricate the O-ring.

Use: 1161761, Grease

47
IMG-380723
 

Install the hose.

Tighten the hose clamp.

Connect the prerouted cable.

Install the catch.

 

Installation

48
IMG-363206
 

Reinstall the removed parts in reverse order.

Fill with coolant and run the engine to operating temperature.

Vent the cooling system and check for leakage.

Post-fill the cooling system if necessary.

49
IMG-370207
 


Tightening torque: Wheel to wheel hub
Stage 1: 20 Nm
Stage 2: 140 Nm