Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

These installation instructions show installation on left hand drive cars.

When installing on right-hand drive cars, perform the procedures on the opposite side and/or mirrored.

Where the procedure differs, the right-hand version is also shown with text and image.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Removal

Remove the panel.

Remove the weatherstrip.

Detach the panel.

Remove the panel.

Remove the panel.

Remove the screws.

Detach the panel.

Disconnect the connector.

Remove the panel.

Fold the carpet to the side.

Locate the rubber grommet under the insulation and press it out.

Vehicles with integrated child safety seat

All vehicles

Remove the panel.

Remove the weatherstrips.

Detach the panel.

Turn the wheel inwards.

Vehicles with headlamp washers

Fold the wing liner to one side.

Place a container under the car.

Take a piece of washer hose. Tie a knot in it and place it on the washer pump to prevent the washer fluid reservoir from emptying.

Release the lock.

Remove the hose.

All vehicles

Turn the wheel inwards.

Remove the screws.

Fold the wing liner to one side.

Disconnect the connector, if applicable.

Release the connector's catch.

Disconnect the connector.

Open the hood.

RHD: The procedure is carried out on the opposite side.

RHD: The procedure is carried out on the opposite side.

Disconnect the connector.

Raise the car.

Remove the screws.

Remove the clips.

Remove the screws.

Remove the clips.

Repeat on the other side.

Repeat on the other side.

Request the aid of a colleague for this procedure.

Disconnect the connector for the fog lamp.

Release the catches.

Repeat on the other side.

The part is not to be reused.

The part is not to be reused.

Accessory installation

Repeat on the other side.

Put the wiring in the Bumper cover without installing the wiring.

RHD: The cable harness is positioned mirrored.

Repeat on the other side.

Repeat on the other side.

Repeat on the other side.

Use: , Electrical tape

Left hand drive vehicles

Remove the nuts.

Pull the wiring through.

Install the cable.

Right-hand drive vehicles

All vehicles

Pull the wiring through.

Insert the cable in to the passenger compartment, adjust the cable length out into the engine compartment and secure the rubber grommet.

Left hand drive vehicles

Remove the tape.

Release the connector's secondary lock.

Connect the pre-routed cables to the 6-pin connector.

Depress the secondary lock.

Right-hand drive vehicles

Remove the tape.

Release the connector's secondary lock.

Connect the pre-routed cables to the 6-pin connector.

Depress the secondary lock.

All vehicles

Right-hand drive vehicles

Fold the insulation to one side.

All vehicles

Pull the wiring through.

Pull the wiring through.

Disconnect the connector, if applicable.

Attach the connector to the wiring harness.

Use: , Electrical tape

The connector is not to be used.

Disconnect the connectors.

The part is not to be reused.

Install component that comes with the accessory kit.

Connect the connectors.

Attach any excess wire to the wiring harness.

Installation

Place the Bumper Cover in position for installation.

Connect the connectors.

Connect the connector.

Reinstall the removed parts in reverse order.

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 30765568