2011 L.H.D

Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
S60 2011
S60 (11-18) 2011

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313300161.431285082, 31359221, 31339968
Parking assistance, rear




Equipment
IMG-275777
A0000162
IMG-239664
IMG-330288
IMG-333288
IMG-333293
IMG-332314

IMG-341611


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Note!

Some steps in these installation instructions are presented with illustration only.


1
IMG-360922
 

Applies to cars with Skid plate.


Caution!

For information about painting and installation of the middle cradles and sensors.

See installation instructions:31265633 Skidplate, rear bumper.


2
IMG-340635
 

3
IMG-344142
 

  • Clean the sensors. Use: Isopropanol

  • Allow to dry.

4
IMG-344141
 

  • Carefully mat the surface down. Use: Glasspaper, grade P1000

5
IMG-344142
 

  • Clean the sensors again. Use: Isopropanol.

  • Allow to dry.

  • Avoid contact with the cleaned surfaces.

6
IMG-344251
 


Caution!

Protect the connections' contact surfaces against paint.


  • Paint the sensors in the same colour code as the vehicle.

  • Use Volvo Touch-up paint (Only use base coat.)

  • Use: Volvo 2-K Varnish. P/N: 31335447.


Note!

Also read the instructions on the spray can.


7
IMG-333934
 


Caution!

The paint must have dried after the first application.


8
IMG-332193
 

  • Turn the ignition key to position 0.


Note!

Wait at least one minute before unplugging the connectors or removing other electrical equipment.


9
IMG-292804
 

10
IMG-292806
 

  • Fold back the mat.

11
IMG-292823
 

  1. Remove the cable harness clips.

  2. Unplug the connector.

12
IMG-292826
 

13
IMG-292827
 

Applies to vehicles with Four-C (Active chassis)

 
14
IMG-340983
 

Applies to all models

15
IMG-340984
 

16
IMG-340985
 

17
IMG-340987
 

18
IMG-293006
 

Applies to cars with an automatic transmission

19
IMG-293007
 

  • Release the shift-lock function.

20
IMG-340981
 

Applies to all models

21
IMG-340636
 

22
IMG-340637
 

23
IMG-340638
 

24
IMG-340639
 

  • Reinstall the detached components in reverse order.

25
IMG-340640
 

26
IMG-340642
 

27
IMG-340641
 

28
IMG-340643
 

29
IMG-340644
 

Applies to vehicles with keyless locking systems

30A
IMG-340645
30B
IMG-340646
 

Illustrations A and B

31
IMG-340647
 

Applies to all models

  • Locate the 4 markings on the inside of the bumper cover.

32
IMG-340648
 

  • Use: Scriber.

33
IMG-340649
 

  1. Ø 3 mm (7/64")

  2. Ø 10 mm (25/64")

34
IMG-340650
 

  • Use special tool: 9997234 Hole tool


Caution!

The cutting part of the tool must be on the outside of the cover.


35
IMG-340651
 

  • Clean the surfaces. Allow to dry.

    Use: Isopropanol

36
IMG-341991
 

  • Clean the surfaces. Allow to dry.

    Use: Isopropanol

37
IMG-340653
 

  • Clean the surfaces. Allow to dry.

    Use: Isopropanol

38
IMG-340654
 

  • Apply a thin and even layer of activator. Allow to dry for at least 10 minutes. Use: 8637076 Activator.

39
IMG-341992
 

  • Apply a thin and even layer of activator. Allow to dry for at least 10 minutes. Use: 8637076 Activator.

40
IMG-340656
 

  • Apply a thin and even layer of activator. Allow to dry for at least 10 minutes. Use: 8637076 Activator.

41
IMG-340657
 

42
IMG-340658
 

43
IMG-340660
 

44
IMG-340659
 

45
IMG-340661
 

Applies to vehicles with keyless locking systems

46
IMG-340662
 

47
IMG-340663
 

48
IMG-340664
 

49
IMG-340666
 

Applies to all vehicles

50A
IMG-340667
50B
IMG-340668
 

Illustrations A and B

  • Check that the rubber bushing closes tight against the body.

51
IMG-340669
 

52
IMG-342946
 

Applies to vehicles without keyless locking systems

53
IMG-342947
 

Applies to vehicles without keyless locking systems

  • Cut off any excess.

54
IMG-340671
 

Applies to vehicles with keyless locking systems

55
IMG-340672
 

Applies to all models

56
IMG-340673
 

57
IMG-341997
 

  • Locate the pre-routed connector.

58
IMG-340676
 

59
IMG-340681
 

60
IMG-340682
 

61
IMG-340686
 

Applies to the right-hand side

62
IMG-340688
 

63
IMG-340689
 

  • Prepare and install one cradle at a time.

64
IMG-340690
 

65
IMG-340691
 

Note the location of the cradles.

  • Repeat the steps for the other cradles.

66
IMG-340692
 

67
IMG-340694
 

  • Press the cradle so that the tape is secured.

68
IMG-340695
 

  • Repeat the steps for the other cradles.

69
IMG-340696
 

  • Place the cable in the cover.

70
IMG-340697
 

  • Connect the two painted sensors to the two outer connections.

71
IMG-340698
 

72
IMG-340699
 

73
IMG-341996
 

74
IMG-340701
 

75
IMG-340702
 

76
IMG-342948
 

Applies to vehicles without keyless locking systems

77
IMG-342949
 

Applies to vehicles without keyless locking systems

  • Cut off any excess.

78
IMG-340705
 

Applies to vehicles with keyless locking systems

79
IMG-340706
 

Applies to all vehicles

  • Reinstall the detached components in reverse order.

80
IMG-242268
 

  • Download software (application) for the accessory's function according to service information in VIDA. See VIDA or accessories catalogue for article number on software.

© Volvo Car CorporationParking assistance, rear- 31330016 - V1.4
volvocars.com
Lifestyle Collection
Svenska
Find a Dealer
Sweden

Cookies Legal Disclaimer Privacy Policy Copyright

Copyright © 2024 Volvo Cars. All rights reserved.