Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

When installing, the car must retain a temperature of 20 degrees C.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Disconnecting the battery

Open the tailgate.

Remove the panel.

Remove the battery's negative cable.

Removal

Make sure that the components are not mixed up at the installation.

Remove the marked part.

Repeat on the other side.

Remove the screws.

Fold the wing liner aside.

Repeat on the other side.

Remove the part carefully

Release the catches.

Remove the part carefully

Loosen the clips.

Remove the part carefully

Remove the marked part.

Release the catches.

Remove the part carefully

Repeat the steps when removing on opposite side.

Locate the connector.

Release the connector's catch.

Disconnect the connector.

Remove the screws.

Request the aid of a colleague for this procedure.

Remove the marked part.

Remove the nuts.

The part is to be reused.

Repeat on the other side.

The part is not to be reused.

Accessory installation

Install component that comes with the accessory kit.

Install the nuts

Repeat on the other side.

Vehicles with weld nut

Install component that comes with the accessory kit.

Repeat on the other side.

Tighten the nuts.

Tighten the screw.

Tightening torque: Tow hitch member mounting to body frame
Stage 1: 50 Nm
Stage 2: 30 Degree

Repeat on the other side.

Vehicles without weld nut

Install the screw.

Repeat on the other side.

Install the nut.

Repeat on the other side.

Tightening torque: Tow hitch member mounting to body frame
Stage 1: 50 Nm
Stage 2: 30 Degree

Repeat on the other side.

Alternative 1

Alternative 2

Cut following the dotted lines.

Fold marked part aside.

Fold marked part aside.

All vehicles

Install component that comes with the accessory kit.

Locate relevant marking.

Position/route the cable harness as illustrated.

Install the wiring harness.

Install component that comes with the accessory kit.

Removal

Remove the marked part.

Remove the marked part.

Vehicles with TV-receiver

Remove the marked part.

1. Remove the marked part.

2. Remove the screw.

3. 
   Tightening torque: Panel, to D-Pillar , 4.5 Nm
   

Remove the panel.

Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones.

Remove the nut.

Remove the panel.

Vehicles with seven seats

Vehicles with TV-receiver

Remove the marked part.

Remove the panel.

Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones.

Remove the marked part.

Remove the screws.

Tightening torque: Cargo anchor, to body , 13 Nm

Remove the panel.

Remove the screw.

Vehicles with air suspension

Loosen the component indicated. Do not remove it.

Use: Interior trim remover

Disconnect the connector.

Vehicles with TV-receiver

Detach the panel.

Disconnect the connectors.

Disconnect the connectors.

Remove the screws.

Remove the nut.

Lift the marked component up

Applies to all other vehicles

Remove the marked part.

Release the catch.

Remove the marked part.

Fold the insulation aside.

Locate the rubber grommet under the insulation and press it out.

Remove the marked part.

The part is not to be reused.

Accessory installation

Vehicles manufactured before 2022w22

Remove the marked part.

The part is not to be reused.

Install component that comes with the accessory kit.

Route the wiring harness into the passenger compartment.

Fasten the wiring harness using the existing clips.

Vehicles manufactured from 2022w22

Route the wiring harness into the passenger compartment.

Fasten the wiring harness using the existing clips.

All vehicles

Route the cable harness to the existing cable harness.

Tighten the cable tie.

Ground connection

Remove the nut.

The part is to be reused.

Release the locks.

Remove the marked part.

The part is not to be reused.

Position/route the cable harness as illustrated.

Connect the prerouted cable.

Tighten the nut.

Tightening torque: M6 , 10 Nm

Orientation view

Removal

Alternative 1

Remove the marked part.

The part is not to be reused.

Alternative 2

Remove the marked part.

The part is not to be reused.

Disconnect the connector.

The part is not to be reused.

Accessory installation

Pull the wiring through.

Use special tool: T9512932, Tension spring

Alternative 1

Connect the connector.

Install component that comes with the accessory kit.

Alternative 2

Connect the connector.

Connect the prerouted cable.

Install component that comes with the accessory kit.

All vehicles

Clean the surface.

Use: 1161721, Isopropanol

Wipe dry.

Clean the surface.

Use: 1161721, Isopropanol

Wipe dry.

Connect the prerouted cables.

Locate the pre-routed connectors.

Disconnect the connector, if applicable.

The part is not to be reused.

Connect the connectors.

Remove the protective film.

Install component that comes with the accessory kit.

Install component that comes with the accessory kit.

Install component that comes with the accessory kit.

Removal

Vehicles manufactured before 2022w22

Locate relevant marking.

Scribe/mark up

Apply tape to the other side, opposite the marking lines.

Remove the marked part.

Use: Air-powered air saw

Deburr edges

Remove the tape.

Vehicles manufactured from 2022w22

Locate relevant marking.

Apply tape to the other side, opposite the marking lines.

Remove the marked part.

Use: Air-powered air saw

Deburr edges

Remove the tape.

Vehicles with skidplate (accessory)

Cut following the dotted lines.

Installation

Request the aid of a colleague for this procedure.

Connect the connector.

Reinstall the bumper.

Request the aid of a colleague for this procedure.

Reinstall the removed part.

Ensure that all clips engage.

Reinstall the removed parts in reverse order.

Connecting the battery

Reinstall the battery's negative cable.

Tightening torque: Battery cable for battery , 6 Nm

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 30644822

Check

Press the button.

Fold out the towbar.

If the components rub against each other, adjustments must be made to correct this.

1. Left indicator lamp

2. Fog tail lamps.

3. Ground connection

4. Right indicator lamp

5. Right position lamp

6. Brake light

7. Left position lamp

8. Back-up lamp

9. Battery voltage, constant

10. Battery voltage, ignition on

11. Ground connection

12. Not connected

13. Ground connection

Press the button.

Fold in the towbar.