Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
S60 2017
S60 (11-18) 2017

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
314082471.031373091
Parking assistance, rear




 

Special tools

 

999 5919 PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Tool number:999 5919

Tool description:PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Tool boards:46

 

999 7234 Hole stamp

Tool number:999 7234

Tool description:Hole stamp

Tool boards:80


Materials

Designation

Part number

Isopropanol

1161721

Sand paper P1000

Volvo Original Touch-up paint

Varnish 2-component

31335447

Activator

8637076


Equipment
IMG-275777
A0000162
IMG-239664

IMG-377522

IMG-377521


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Further information

2
 

After installation, the car must not be washed for 48 hours

When installing, the car must retain a temperature of 20 degrees C.

3
IMG-363036
 

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

  1. Used for focused component, the component with which you will do something.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

 

Paintwork

4
IMG-373951
 
5
IMG-344142
 

Clean the surface.

Use: 1161721, Isopropanol

6
IMG-344141
 

Matt the surface gently.

Use: , Sand paper P1000

7
IMG-344142
 

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

8
IMG-344251
 

Caution!
Protect connector surfaces against paint spray.


Note!
Paint the sensors the same colour code as the vehicle.

Use: , Volvo Original Touch-up paint

Use base coat only.

Use: 31335447, Varnish 2-component

Also see the instructions on the container.

9
IMG-333934
 

Caution!
First the paint must dry after painting.

 

Removal

10
IMG-332193
 

Set the ignition key to position 0.

11
IMG-377640
 

Note!
Orientation view

12
IMG-372212
 

Measure and mark as illustrated.

13
IMG-372210
 
14
IMG-372209
 


Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

15
IMG-372207
 
 

Accessory installation

16
IMG-372208
 
 

Removal

17
IMG-340640
 

Remove the screws.

Repeat on the other side.

18
IMG-377496
 

Remove the screws.

19
IMG-340641
 

Repeat on the other side.

20
IMG-340643
 
21
IMG-340644
 

Caution!
Place the Bumper Cover on a suitable surface.

Disconnect the connector, if applicable.

 

Vehicles with keyless entry

22
IMG-340645
 
23
IMG-340646
 

Disconnect the connector.

The cable harness must not be reused.

 

Vehicles with integrated Exhaust End Pipes

24
IMG-377518
 

Remove the clip.

Repeat on the other side.

25
IMG-377520
 

The part is not to be reused.

 

Applies to all other vehicles

26
IMG-377812
 

The part is not to be reused.

 

Accessory installation

 

Vehicles with integrated Exhaust End Pipes

27
IMG-377523
 

Install component that comes with the accessory kit.

28
IMG-377518
 

Install the clip(s).

Repeat on the other side.

 

Applies to all other vehicles

29
IMG-377814
 

Install component that comes with the accessory kit.

 

All vehicles

30
IMG-377497
 

Locate the markings for the positions.

31
IMG-377498
 

Mark the centre.

32
IMG-377499
 
33
IMG-377500
 

Caution!
Sharp end of tool must be on outside of cover.


Use special tool: T9997234, Hole stamp

34
IMG-377506
 

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

35
IMG-377524
 

Clean the surface.

Use: 1161721, Isopropanol

Allow to dry.

36
IMG-377527
 

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

37
IMG-377508
 

Clean the surfaces.

Use: 1161721, Isopropanol

Allow to dry.

38
IMG-377509
 

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

39
IMG-377525
 

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

40
IMG-377528
 

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

41
IMG-377510
 

Apply a thin and even layer.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

 

Removal

42
IMG-340657
 
43
IMG-340658
 
44
IMG-340660
 
45
IMG-340659
 
 

Vehicles with keyless entry

46
IMG-340661
 
47
IMG-340662
 
48
IMG-340663
 
49
IMG-340664
 
 

Accessory installation

 

All vehicles

50
IMG-377511
 
51
IMG-340667
 
52
IMG-340668
 

Caution!
Make sure that the rubber grommet seals properly to the body.

53
IMG-340669
 
54
IMG-340671
 
55
IMG-340672
 
56
IMG-340673
 
57
IMG-341997
 

Locate the existing connector in the vehicle's cable harness.

58
IMG-340676
 

Connect the connector.

59
IMG-340681
 

Connect the prerouted cable.

60
IMG-377539
 

Remove the protective film.

61
IMG-377512
 

Note!
Ensure that the tape is fixed to the surface.

62
IMG-377513
 

Note!
Prepare and install one holder at a time.

63
IMG-340690
 

Remove the protective film.

64
IMG-377514
 

Note position of components.

65
IMG-340692
 
66
IMG-340694
 

Note!
Ensure that the tape is fixed to the surface.

67
IMG-340695
 
68
IMG-377529
 

Remove the protective film.

Install component that comes with the accessory kit.

69
IMG-377530
 

Remove the protective film.

Install component that comes with the accessory kit.

70
IMG-377543
 

Put the wiring in the Bumper cover without installing the wiring.

71
IMG-373743
 

Connect the two painted sensors to the external connections.

72
IMG-377515
 
73
IMG-377758
 
74
IMG-377638
 

Fasten the wiring harness using the existing clips.

75
IMG-377548
 
76
IMG-377549
 
 

Vehicles with keyless entry

77
IMG-340705
 

Connect the connector.

 

Vehicles without keyless entry

78
IMG-377757
 
 

All vehicles

79
IMG-340706
 

Place the Bumper Cover in position for installation.

Connect the connector.

80
IMG-377070
 

Reinstall the removed parts in reverse order.

81
IMG-242268
 

Download software (application) for the accessory's function according to the service information in VIDA.

Order and download software according to: 31266966