Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

7. Used for accessory components.

Removal

Set the vehicle to Inactive mode.

Open the hood.

Raise the car.

Remove the marked detail/details.

Use: Pliers 31423632

Remove the screws.

Remove the marked part.

Remove the screws.

Remove the clips.

Remove the nuts.

Remove the screws.

Remove the clip.

Remove the marked part.

Remove the clips.

Remove the screws.

Remove the marked part.

Remove the screws.

Remove the clips.

Remove the screws.

Loosen the component indicated. Do not remove it.

Applies to the left-hand side:

1. Remove the connector from its attachment.

2. Remove the cable harness clips.

3. Remove the hose.

Applies to the right-hand side

1. Remove the cable harness clips.

2. Remove the hose.

Remove the marked part.

Drain the cooling system according to service information in VIDA:

Information / Repair / Cleaning, Inspection and Adjustment / 2 Engine with mountings and equipment / 26 Cooling system / 261 radiator and connections / Cooling system – draining, charging and bleeding.

Use special tool: T9997669, Key

Accessory installation

Locate relevant marking.

Saw in a way so that the marking remains.

Use: Air-powered air saw

Install component that comes with the accessory kit.

Check that the flange of the part is in full contact with bumper cover.

Adjust the hole with a file or knife as necessary.

Install component that comes with the accessory kit.

Install components that come with the accessory kit.

Install component that comes with the accessory kit.

This is used as a counterhold.

Tighten the nut.

Use hands only.

Ground connection

Remove the nut.

The item is to be reused.

Position/route the cable as illustrated.

Connect the prerouted cable.

Install the nut.

Tightening torque: M6 , 10 Nm

Position/route the cable as illustrated.

Install the cables.

Use a cable tie

Lubricate the O-ring.

Install the marked component.

Install the catch.

Use detail according to image.

Place the cable tie as illustrated.

Position/route the cable as illustrated.

Tighten the cable tie.

Position/route the cable as illustrated.

Position/route the cable as illustrated.

Position/route the cable as illustrated.

Use a cable tie

Install a clips onto the upper edge of the subframe.

Place the cable tie as illustrated.

1. Steering gear

2. Cable harness

3. Engine heater cable

Position/route the cable as illustrated.

Install the cable.

Undo the hose from the connection.

Remove part of component according to image.

Remove the clip.

Remove a piece of the protective cover.

Vehicles with 2WD

Loosen the clip.

All vehicles

Remove the clip.

Remove part of component according to image.

Clean the surface.

Remove the protective film.

Install components that come with the accessory kit.

Tighten the bolts.

Vehicles with 2WD

Install the marked component.

All vehicles

Assemble components that come with the accessory kit.

Connect the hose.

Attach the hose clamp

Connect the hose.

Tighten the hose clamp.

Use: Scribe

Use: Pop rivet pliers

Lubricate the O-ring.

Connect the cable.

Install the catch.

Fasten the cable tie without tightening.

Adjust the cable position so that it can follow the motions of the engine.

Tighten the cable tie.

Tighten the cable ties.

Installation

Fill the cooling system according to the service information in VIDA:

Use special tool: T9997669, Key

Use special tool: T9512955, Cover

Use special tool: T9814192, Hose

Use special tool: T9512957, Coolant Reservoir

Reinstall the removed parts in reverse order.

Tightening torque: Aluminum wheel rim to wheel hub
Stage 1: 4 Nm
Stage 2: 50 Nm
Stage 3: 140 Nm