| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
|  | | IMG-400004 |
|
| | Caution!
Attach the antenna wires using tape. Cable ties or similar must not be used. |
Caution!
Observe caution when handling fibre optic cables. |
Caution!
Make sure that the fiber optic cables are not bent to a radius of less than 25 mm. |
|
| | |
|  | | IMG-400010 |
|
| | Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components. Used for accessory components.
|
| | |
|  | | IMG-342372 |
|
| | Repeat on the other side. |
|  | | IMG-360124 |
|
| | Remove the marked part. Disconnect any connector(s). |
|  | | IMG-377298 |
|
| | |
|  | | IMG-377299 |
|
| | Loosen the marked detail. |
|  | | IMG-377300 |
|
| | Loosen the marked detail. |
|  | | IMG-377302 |
|
| | |
|  | | IMG-377309 |
|
| | |
|  | | IMG-377320 |
|
| | |
|  | | IMG-460936 |
|
| | |
|  | | IMG-460937 |
|
| | |
|  | | IMG-360186 |
|
| | |
|  | | IMG-308353 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
|  | | IMG-308354 |
|
| | |
|  | | IMG-286863 |
|
| | Caution!
The front and upper sill panel must be removed and installed as one unit. |
|
|  | | IMG-308355 |
|
| | |
|  | | IMG-308356 |
|
| | |
|  | | IMG-329150 |
|
| | |
|  | | IMG-340980 |
|
| | Remove the screws.
Tightening torque: Front seat to body
, 40 Nm
|
|  | | IMG-303005 |
|
| | |
|  | | IMG-303006 |
|
| | Remove the screws.
Tightening torque: Front seat to body
, 40 Nm
|
|  | | IMG-400002 |
|
| | Remove the battery's negative cable. |
| | |
|  | | IMG-380657 |
|
| | |
| | |
|  | | IMG-380655 |
|
| | |
|  | | IMG-380656 |
|
| | |
| | |
|  | | IMG-329151 |
|
| | |
|  | | IMG-373198 |
|
| | |
|  | | IMG-329209 |
|
| | Loosen the screws. Disconnect the connector. |
|  | | IMG-382639 |
|
| | Disconnect the connector, if applicable. |
|  | | IMG-329153 |
|
| | Caution!
Be extra careful when removing or installing this component. |
|
|  | | IMG-460418 |
|
| | Remove the screws. Loosen the marked detail.
Tightening torque: M6
, 10 Nm
|
| | Vehicles with High Performance Sound |
|  | | IMG-460425 |
|
| | Disconnect the connector. |
| | Vehicles with Premium Sound |
|  | | IMG-460422 |
|
| | Disconnect the connector. |
|  | | IMG-460609 |
|
| | |
| | |
|  | | IMG-460610 |
|
| | Loosen the tape temporarily. The item is to be reused. |
|  | | IMG-460611 |
|
| | |
|  | | IMG-460426 |
|
| |
Use special tool: T9512620, Stripping tool (for wiring)
|
|  | | IMG-460764 |
|
| | Use detail according to image. |
|  | | IMG-460428 |
|
| |
Use special tool: T9512620, Stripping tool (for wiring)
|
|  | | IMG-460373 |
|
| | |
|  | | IMG-460547 |
|
| |
Use special tool: T9512785, Crimping tool (included in 9512669)
|
|  | | IMG-460375 |
|
| | Caution!
Make sure that the surrounding components are protected from heat. |
Use special tool: T9512777, Hot-air gun
|
|  | | IMG-460376 |
|
| | |
|  | | IMG-460660 |
|
| | |
|  | | IMG-460520 |
|
| | |
|  | | IMG-460836 |
|
| | |
|  | | IMG-460512 |
|
| | |
|  | | IMG-460511 |
|
| | Connect the ground cable. Reinstall the screw. |
|  | | IMG-460516 |
|
| | Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
|  | | IMG-460839 |
|
| | Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
|  | | IMG-460840 |
|
| | Fold the floor carpet back. |
|  | | IMG-460843 |
|
| | Caution!
Make sure that the fiber optic cables are not bent to a radius of less than 25 mm. |
Place the overlap of the cable mat under the amplifier. Reinstall the removed part. Reinstall the screws.
Tightening torque: M6
, 10 Nm
|
| | |
|  | | IMG-378835 |
|
| | |
|  | | IMG-460935 |
|
| | Loosen the marked detail. Use: Electrician's screwdriver
Remove the screw. |
|  | | IMG-343420 |
|
| | Note!
The clips consist of two parts. |
Note!
The top of the guide sleeve is designed to break off. |
Remove the panel. Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones. |
|  | | IMG-377345 |
|
| | |
|  | | IMG-377347 |
|
| | Release the catches. Remove the panel. |
|  | | IMG-307608 |
|
| | |
|  | | IMG-307609 |
|
| | |
|  | | IMG-377342 |
|
| | |
|  | | IMG-346921 |
|
| | |
|  | | IMG-346811 |
|
| | |
|  | | IMG-346861 |
|
| | Loosen the screws. Remove the panel. |
|  | | IMG-377350 |
|
| | |
|  | | IMG-377352 |
|
| | Disconnect the connector, if applicable. Remove the panel. |
| | Vehicles with subwoofer speaker |
|  | | IMG-395146 |
|
| | Disconnect the connector. |
|  | | IMG-395147 |
|
| | Remove the nuts. Remove the screws. |
|  | | IMG-395149 |
|
| | |
| | |
| | |
|  | | IMG-460480 |
|
| | Assemble components that come with the accessory kit. |
|  | | IMG-460483 |
|
| | Place the component where indicated in the graphic. |
|  | | IMG-460484 |
|
| | Install component that comes with the accessory kit. |
|  | | IMG-460844 |
|
| | |
|  | | IMG-460848 |
|
| | |
|  | | IMG-460871 |
|
| | |
|  | | IMG-460550 |
|
| | Install component that comes with the accessory kit. |
|  | | IMG-460910 |
|
| | Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
|  | | IMG-460912 |
|
| | Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
|  | | IMG-460915 |
|
| | Caution!
Ensure that wires cannot rub against the backrest bracket. |
Route the cable harness to the existing cable harness. Install the wiring harness. Use a cable tie |
|  | | IMG-460925 |
|
| | |
| | |
|  | | IMG-460984 |
|
| | Caution!
Take extra care not to crease the headliner. |
|
|  | | IMG-460986 |
|
| | |
|  | | IMG-460996 |
|
| | Loosen the clip. Disconnect the connectors. Remove the marked part. |
| | |
|  | | IMG-460766 |
|
| | Use details according to image. |
|  | | IMG-460546 |
|
| | Assemble components that come with the accessory kit. Depress the secondary lock. |
|  | | IMG-461000 |
|
| | Assemble components that come with the accessory kit. |
|  | | IMG-461002 |
|
| | Connect the connectors. Install the clip(s). Tighten the screw. |
|  | | IMG-461019 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
|  | | IMG-461122 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
|  | | IMG-461134 |
|
| | Remove the clip. Fold the insulation aside. |
|  | | IMG-461150 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
|  | | IMG-461151 |
|
| | Fold the insulation aside. |
|  | | IMG-461152 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
|  | | IMG-461158 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
|  | | IMG-461161 |
|
| | Caution!
Ensure that wires cannot rub against the backrest bracket. |
Route the wire adjacent to existing wirings. Install the cable. Use tape |
|  | | IMG-461197 |
|
| | |
|  | | IMG-461200 |
|
| | Caution!
Make sure that the fiber optic cables are not bent to a radius of less than 25 mm. |
Position the cable harness excess as illustrated. Install the wiring harness. Use tape |
| | Reinstall the removed parts in reverse order. |
|  | | IMG-400003 |
|
| | Reinstall the battery's negative cable. |
|  | | IMG-400006 |
|
| | Order and download software according to VIDA/SOFTWARE. Order and download software according to: 31268617
Download software (application) for the accessory's function according to the service information in VIDA. Order and download software according to: 31285168
|
