| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | IMG-400004 |
|
| | Caution! Attach the antenna wires using tape. Cable ties or similar must not be used. |
There may be parts in the accessories kit that are not needed for this installation. |
| | |
| | IMG-363036 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | IMG-426135 |
|
| | |
| | |
| | Note! The removal steps may contain installation details. |
|
| | IMG-427495 |
|
| | |
| | IMG-425275 |
|
| | |
| | IMG-425276 |
|
| | Fold marked part aside. Remove the screw. Tightening torque: Seat belt guide, to Bracket
, 4.4 Nm
|
| | IMG-419062 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-425278 |
|
| | Remove the panel. Use hands only. |
| | IMG-411349 |
|
| | |
| | IMG-411350 |
|
| | Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304
|
| | IMG-411351 |
|
| | Remove the screw. Tightening torque: M8
, 24 Nm
|
| | IMG-425079 |
|
| | Remove the screw. Tightening torque: Safety belt retractor rear to body
, 40 Nm
|
| | IMG-425287 |
|
| | |
| | IMG-414611 |
|
| | |
| | IMG-415830 |
|
| | Repeat on the other side. |
| | IMG-415831 |
|
| | Remove the screw. Tightening torque: M6
, 10 Nm
Repeat on the other side. |
| | IMG-425226 |
|
| | |
| | IMG-425291 |
|
| | |
| | IMG-425295 |
|
| | |
| | IMG-425300 |
|
| | Remove the panel. Disconnect any connector(s). |
| | IMG-428680 |
|
| | Disconnect the connectors. |
| | IMG-428682 |
|
| | |
| | IMG-428683 |
|
| | Remove the nuts. Remove the marked part. |
| | IMG-423458 |
|
| | Remove the screws. Remove the marked part. The part is not to be reused. |
| | |
| | IMG-430010 |
|
| | |
| | IMG-430011 |
|
| | Place the component where indicated in the graphic. Install the nuts |
| | IMG-425377 |
|
| | Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-423030 |
|
| | Adjust the component to a horizontal position. |
| | IMG-428708 |
|
| | |
| | IMG-430890 |
|
| | Connect the connector. Position/route the cable as illustrated. Install the cable. Use a cable tie |
| | IMG-430892 |
|
| | Position/route the cable as illustrated. Install the cable. Use a cable tie |
| | IMG-428357 |
|
| | Note! Position the template so that its surfaces are aligned against the panel. |
|
| | IMG-428358 |
|
| | Use a drill with the stated size |
| | IMG-428360 |
|
| | Use a drill with the stated size |
| | IMG-430031 |
|
| | |
| | IMG-430032 |
|
| | Note! Do not fully tighten the nut yet. |
Install the nut. |
| | IMG-428368 |
|
| | Note! Position the holder horizontally on the panel. |
Tighten the nut. Use hands only. |
| | IMG-428370 |
|
| | Connect the prerouted cable. |
| | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number. |
| | |
| | IMG-400000 |
|
| | Reinstall the removed parts in reverse order. |
| | IMG-422420 |
|
| | Place the manual for this accessory in a suitable location in the car. |