Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC60 2014
XC60 (-17) 2014

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
316646181.231373742
Protective tape, rear bumper




 

Materials

Designation

Part number

Isopropanol

1161721


Equipment
IMG-244945
IMG-221380

IMG-374018


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Conditions

2
 

When installing, the car must retain a temperature of 20 degrees C.

After installation, the car must not be washed for 48 hours

After installation, the car must not be driven for 2 hours

 

Color symbols

3
IMG-363036
 

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

  1. Used for focused component, the component with which you will do something.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

 

Accessory installation

4
IMG-374184
 

Clean the Bumper Cover surface.

Allow to dry.

5
IMG-374185
 

Use suitable tape to indicate the center.

6
IMG-374121
 

Use suitable tape to indicate the center.

7
IMG-345624
 

Cut off a piece of the transparent foil, as indicated.

8
IMG-345997
 

Cut off a piece of the transparent foil, as indicated.

9
IMG-374197
 

Center the Bumper Cover, using the tape marks and the values in the graphic.

10
IMG-374196
 

Note!
Make sure that the Bumper Protection is installed on the flat bumper surface only, not covering any sharp radius.

11
IMG-374202
 

Use appropriate tape to mark the position.

12
IMG-374199
 

Clean the Bumper Cover surface.

Allow to dry.

Use: 1161721, Isopropanol

13
IMG-378893
 

Clean the lower transparent foil.

Allow to dry.

Use: 1161721, Isopropanol

14
IMG-345623
 

Cut in the lower transparent foil in the middle.

15
IMG-378604
 

Pull off the top protection foil, if applicable.

16
IMG-423761
 

Caution!
Make sure that the surface is clean and free of foreign material.

17
IMG-345942
 

Adjust the position of the Bumper Protection using the tape marks.

18
IMG-347431
 

Note!
Use tape to temporarily fix the bumper cover in the correct position.

19
IMG-347451
 

Note!
Touching the adhesive surface will impair rebonding.

Partly fold back the transparent foil to expose the sticky surface.

20
IMG-378667
 

Use suitable tool to squeeze out any trapped air bubbles.

21
IMG-378668
 

Pull off the rest of the transparent foil and press by hand on the Bumper protection to make it cling to the Bumper Cover.

Use suitable tool to squeeze out any trapped air bubbles.

22
IMG-378669
 

Pull off the rest of the transparent foil and press by hand on the Bumper protection to make it cling to the Bumper Cover.

Use suitable tool to squeeze out any trapped air bubbles.

23
IMG-374200
 

Thoroughly press, by hand, all over the Bumper Protection to make it cling properly.

Use suitable tool to squeeze out any trapped air bubbles.