Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC60 2014
XC60 (-17) 2014

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313246331.031414859, 31373184
Towbar, wiring, 13-pin




IMG-264110




 
Equipment
IMG-345497
IMG-239664

IMG-348782


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

1
IMG-332193
 
  • Turn the ignition switch to position 0.


Note!

Wait at least three minutes before disassembling the connectors or removing other electrical equipment.


2
IMG-346921
 

Removal

3
IMG-346922
 
4
IMG-346923
 
5
IMG-346937
 
6
IMG-347068
 
  • Remove the panel.

 

Accessory installation

7
IMG-285983
 

Accessory installation

Vehicles with fixed towbar

Tightening torque: M5, 5 Nm

8
IMG-297725
 

  • Remove the rubber grommet.

    It must not be reused.

9
IMG-285984
 

  • Pull the wiring through. Check that the rubber grommet seals against the bodywork.

10
IMG-294263
 

 
11
IMG-294303
 

Vehicles with detachable towbar

  • Remove the rubber grommet.

    It must not be reused.

12
IMG-286026
 

  • Pull the wiring through. Check that the rubber grommet seals against the bodywork.

13
IMG-286028
 

Tightening torque: M5, 5 Nm

 

All vehicles

14
IMG-366117
 

All vehicles

15
IMG-366120
 

  • Thread the cable harness through.

16
IMG-366072
 

  • Plug in the connector.

 
17
IMG-366140
 

Applies to vehicles with DVD reader

  • Remove the screws.

18
IMG-366142
 

19
IMG-366146
 

  • Unplug the connectors.

 

Applies to all vehicles

20
IMG-366124
 

Applies to all vehicles

  • Fold aside the insulation.

 
21
IMG-366276
 

Applies to vehicles with chassis numbers up to and including -175378

  • Locate ground terminals.

22
IMG-366471
 


Note!

Connect to an available ground terminal, in one of the three existing.


  • Install the cable and grounding screw.

    Tightening torque: M6, 10 Nm

 
23
IMG-366473
 

Applies to vehicles with chassis numbers from and including 175379-

  • Locate ground terminals.

24
IMG-366131
 


Note!

Connect to an available ground terminal, in one of the three existing.


  • Install the cable and grounding screw.

    Tightening torque: M6, 10 Nm

 

Applies to all vehicles

25
IMG-366316
 

Applies to all vehicles

 
26
IMG-285840
 

Removal

Applies to vehicles with chassis numbers up to and including -175378

  • Press the catches on the cover together for the module RJB-A and remove it.

27
IMG-286143
 

  • Release the catch.

    The cable must be connected to the spare socket on the reverse of the fuse socket F9 on module RJB A.

    Squeeze the pliers together on the fuse holder catch on the module where the cable is to be pressed in, and pull up.

28
IMG-286144
 

  • Carefully pry the joint between the module's inner and outer parts using a weatherstrip tool so that the inner part slides to the side slightly so that the cable terminal can be positioned.

 
29
IMG-294723
 

Installation

  • Install the routed cable in fuse terminal F9

  • Reinstall the catch in the outer part.

30
IMG-286146
 

31
IMG-286147
 

  • Install a 15 A fuse from the kit in terminal F9.

32
IMG-285843
 

 
33
IMG-347281
 

Removal

Applies to vehicles with chassis numbers from and including 175379-. These vehicles only have one fuse holder/relay holder

  • Release the catch.

  • Remove the cover.

34
IMG-347282
 

  • Release the hooks.

35
IMG-338810
 

  • Release the catch.

36
IMG-286144
 

 
37
IMG-334293
 

Installation

  • Install the routed cable in fuse terminal F4

38
IMG-347791
 

39
IMG-347283
 

40
IMG-334399
 

41
IMG-347286
 

  • Reinstall the cover.

 
42
IMG-347021
 

Vehicles with fixed towbar

43
IMG-348026
 

  • Transfer the connector's cradle to the start of the hook's radius.

    Align the connector cradle so that it sits straight.

44
IMG-347886
 

Tightening torque: M8, 24 Nm

45
IMG-347022
 

46
IMG-348017
 


Note!

For correct function, the trailer module (TRM) must be programmed with software before checks can be carried out.


  • Checking the 13 pin connector.


Note!

To activate the trailer module (TRM) at least two light sources (lamps) must be connected. This can be done by connecting test equipment for the trailer connector or a trailer.


Position Function

  1. Left turn signal lamp

  2. Rear fog lamps

  3. Ground terminal

  4. Right turn signal lamp

  5. Right parking lamps

  6. Brake lamp

  7. Left parking lamps

  8. Reversing lamp

  9. Battery voltage, constant

  10. Battery voltage, ignition on

  11. Ground terminal

  12. Not connected.

  13. Ground terminal

47
 
  • Reinstall the detached components in reverse order.