Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Removal

Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Disconnect the connector.

Remove the panel.

Remove the panel.

Disconnect the connector, if applicable.

Remove the panel.

Remove the panel.

Disconnect the connector, if applicable.

Remove the screws.

Remove the panel.

Remove the panel.

Remove the panel.

Use hands only.

Release the catch.

Remove the marked part.

Remove the panel.

Use hands only.

Remove the screw.

Tightening torque: M6 , 10 Nm

Release the lock.

Repeat on the other side.

Remove the marked part.

Remove the panel.

Disconnect the connector, if applicable.

Remove the marked part.

Detach the panel.

Remove the panel.

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

Remove the screws.

Tightening torque: Front seat to body , 40 Nm

Disconnect the connector.

Unhook the cable harness clips.

Remove the screws.

Fold marked part aside.

Remove the marked part.

Repeat on the other side.

Remove the screw.

Tightening torque: M6 , 10 Nm

Repeat on the other side.

Remove the marked part.

Vehicles with keyless entry

All vehicles

Remove the screws.

Remove the marked part.

Disconnect the connectors.

Remove the panel.

Remove the screws.

Remove the panel.

Remove the panel.

Remove the panel.

Remove the screws.

Remove the panel.

Disconnect the connector.

Loosen the screws.

Loosen the exact number of turns indicated in the image.

Use: Interior trim remover

The part is not to be reused.

Accessory installation

Tighten the bolts.

Use special tool: T9814199, Torque wrench

Connect the connector.

Loosen the marked detail/details.

To be repeated in the other end of the component.

Release the catches.

Loosen the marked detail/details.

Use: Scribe

Use: Interior trim remover

To be repeated in the other end of the component.

Use: 988734, Cable tie, 750 mm

Use: , Electrical tape

Pull the wiring through.

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Turn once.

Tear off the excess foam tape.

Pull the wiring through.

Use: 1161150, Lubricant

Wipe off

Remove the cable tie(s).

Pull the wiring through.

Reinstall the removed part.

To be repeated in the other end of the component.

Reinstall the removed part.

To be repeated in the other end of the component.

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

Remove the marked part.

Remove the nut.

Fold marked part aside.

Release the catches.

Fold marked part aside.

Remove the marked part.

Reinstall the removed part.

Install the cable.

Use a cable tie

Reinstall the removed part.

Install component that comes with the accessory kit.

Route the wires adjacent to existing wirings.

Install the cables.

Use a cable tie

Route the wires adjacent to existing wirings.

Install the cables.

Use a cable tie

Route the wires adjacent to existing wirings.

Install the cables.

Use a cable tie

Position/route the cables as illustrated.

Position/route the cables as illustrated.

Remove the marked part.

Remove the marked part.

The part is not to be reused.

Fold marked part aside.

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Position/route the cables as illustrated.

Install the nuts

Connect the prerouted cable.

Position/route the cable as illustrated.

Position the cable harness excess as illustrated.

Install the cable.

Use a cable tie

Connect the prerouted cable.

Position/route the cable as illustrated.

Connect the cable.

Position/route the cable as illustrated.

Remove the nut.

Connect the prerouted cable.

Install the nut.

Tightening torque: M6 , 10 Nm

Fold marked part aside.

1. Release the connector's catch.

2. Release the lock.

3. Disconnect the connector.

Release the connector's catch.

Remove the connector from its attachment.

Remove the tape.

Use special tool: T9512620, Stripping tool (for wiring)

Use special tool: T9512785, Crimping tool (included in 9512669)

Use special tool: T9512785, Crimping tool (included in 9512669)

Use special tool: T9512777, Hot-air gun

Install the connector to its attachment.

Connect the connector.

Reinstall the removed part.

Position/route the cable as illustrated.

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Position/route the cable as illustrated.

Connect the prerouted cable.

Install component that comes with the accessory kit.

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.

Installation

Reinstall the removed parts in reverse order.