| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | After installation, the car must not be washed for 48 hours When installing, the car must retain a temperature of 20 degrees C. |
| | |
| | IMG-363036 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | |
| | IMG-373951 |
|
| | |
| | IMG-344142 |
|
| | Clean the surface. Use: 1161721, Isopropanol
|
| | IMG-344141 |
|
| | Matt the surface gently. Use: , Sand paper P1000
|
| | IMG-344142 |
|
| | Clean the surface. Use: 1161721, Isopropanol
|
| | IMG-377210 |
|
| | Caution! Protect connector surfaces against paint spray. |
Use: , Volvo Original Touch-up paint
Use paint colours according to the colour code given in the image. Use base coat only. Use: 31335447, Varnish 2-component
Also see the instructions on the container. |
| | IMG-333934 |
|
| | Caution! First the paint must dry after painting. |
|
| | |
| | IMG-332193 |
|
| | Set the ignition key to position 0. |
| | IMG-377098 |
|
| | |
| | IMG-372212 |
|
| | Measure and mark as illustrated. |
| | IMG-372210 |
|
| | |
| | IMG-372209 |
|
| | Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304
|
| | IMG-372207 |
|
| | |
| | |
| | IMG-372208 |
|
| | |
| | |
| | IMG-259683 |
|
| | |
| | IMG-259684 |
|
| | |
| | IMG-259754 |
|
| | Remove the screws. Repeat on the other side. |
| | IMG-259756 |
|
| | Caution! Place the Bumper Cover on a suitable surface. |
|
| | |
| | IMG-283030 |
|
| | Locate the markings for the positions. Mark the centre. |
| | IMG-283031 |
|
| | |
| | IMG-273313 |
|
| | Caution! Sharp end of tool must be on outside of cover. |
Use special tool: T9997234, Hole stamp
|
| | IMG-283032 |
|
| | Clean the surfaces. Use: 1161721, Isopropanol
|
| | IMG-377226 |
|
| | Clean the surface. Use: 1161721, Isopropanol
|
| | IMG-283033 |
|
| | Apply a thin and even layer. Use: 8637076, Activator
Allow to dry for at least 10 minutes. |
| | IMG-283028 |
|
| | Apply a thin and even layer. Use: 8637076, Activator
Allow to dry for at least 10 minutes. |
| | |
| | IMG-261414 |
|
| | |
| | IMG-273316 |
|
| | |
| | |
| | IMG-273317 |
|
| | |
| | IMG-273318 |
|
| | |
| | IMG-273319 |
|
| | Locate the pre-routed connector. |
| | IMG-273320 |
|
| | The part is not to be reused. |
| | IMG-273321 |
|
| | Caution! Make sure that the rubber grommet seals properly to the body. |
Install component that comes with the accessory kit. |
| | IMG-273322 |
|
| | |
| | IMG-273323 |
|
| | |
| | IMG-273324 |
|
| | |
| | IMG-377228 |
|
| | Note! Prepare and install one holder at a time. |
|
| | IMG-377239 |
|
| | Note! Ensure that the tape is fixed to the surface. |
Remove the protective film. |
| | IMG-377241 |
|
| | Warning! Make sure to provide adequate ventilation. |
Warning! Wear protective gloves. |
Apply a thin and even layer. Use: 9511027, Glue
Use special tool: T9512950, Glue gun (kit)
Use: 1161730, Mixing pipe
|
| | IMG-297571 |
|
| | |
| | IMG-297572 |
|
| | Note! Apply pressure only where the tape is located. |
|
| | IMG-297573 |
|
| | Note! Hold the part securely at the marker arrows when removing the tool. |
|
| | IMG-377247 |
|
| | Put the wiring in the Bumper cover without installing the wiring. |
| | IMG-247287 |
|
| | |
| | IMG-377248 |
|
| | |
| | IMG-273328 |
|
| | Caution! Hold the newly bonded sensor holder in position whilst pressing the clip into position. |
Install the cable. |
| | |
| | IMG-273330 |
|
| | Request the aid of a colleague for this procedure. Place the Bumper Cover in position for installation. Connect the connector. |
| | IMG-273331 |
|
| | |
| | IMG-377070 |
|
| | Reinstall the removed parts in reverse order. |
| | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. Order and download software according to: 30765571
|