Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC70 2013
XC70 (08-) 2013

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313399881.131332429, 31339994, 31332421, 30758168
Parking assistance camera wide angle front




IMG-354346




 

Materials

Designation

Part number

Low temperature grease

1161427


Equipment
IMG-242205
IMG-345497
IMG-300203
IMG-327738
IMG-239667
IMG-244945
IMG-240693

IMG-353536


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Conditions

2
IMG-332179
 

Set the ignition key to position 0.

Remove the battery's negative cable.

 

Removal

3
IMG-354313
 

Remove the panel.

4
IMG-354315
 

Remove the weatherstrip.

5
IMG-354318
 

Remove the panel.

6
IMG-354319
 

Remove the panel.

7
IMG-344930
 
8
IMG-354320
 
9
IMG-349804
 

Remove the panel.

10
IMG-349806
 

Remove the screws.

11
IMG-345282
 

Remove the screws.

 

Cars with manual transmissions

12
IMG-345747
 

Release the lock ring which is located inside the gear lever boot.

13
IMG-347222
 
 

Cars with automatic transmissions

14
IMG-345283
 
15
IMG-345284
 

Release the shift-lock function.

16
IMG-341878
 

Remove the panel.

17
IMG-346036
 

Remove the panel.

18
IMG-340599
 
  1. Fold the carpet to the side.

  2. Unhook the clip(s).

  3. Disconnect the connector.

19
IMG-353601
 
20
IMG-353602
 

Remove the screws.

21
IMG-347139
 

Remove the panel.

 

Vehicles with the 4C system.

22
IMG-345317
 

Disconnect the connector.

 

All vehicles

23
IMG-349826
 

Caution!
Be careful not to damage the catches.

Remove the panel.

24
IMG-340605
 

Remove the screws.

25
IMG-345296
 
26
IMG-345763
 
 

Accessory installation

27
IMG-345764
 
 

Removal

28
IMG-349942
 

Remove the screws.

29
IMG-349946
 
30
IMG-353492
 

Disconnect the connectors.

31
IMG-349876
 

Remove the panel.

32
IMG-349877
 

Remove the screws.

Remove the panel.

33
IMG-349901
 

Caution!
The number of connectors can vary depending on the vehicle's equipment level.

Disconnect the connectors.

34
IMG-349903
 
35
IMG-353512
 
36
IMG-353511
 

Remove the screws.

37
IMG-349993
 

Remove the panel.

38
IMG-350006
 

Remove the panel.

39
IMG-352301
 

Remove the screws.

On both sides.

40
IMG-352271
 

Remove the panel.

41
IMG-350026
 

Remove the screws.

42
IMG-349999
 

Detach the panel.

43
IMG-349992
 

Disconnect the connector.

 

Accessory installation

44
IMG-350072
 
45
IMG-355161
 

Caution!
Make sure that no part of the wiring harness is trapped.

Facilitate cable routing by temporarily raising the floor bracket using a socket or similar.

Pull the wiring through.

46
IMG-355174
 

Connect the connectors.

47
IMG-355175
 

Tear off the excess foam tape.

48
IMG-355200
 

Route the cable harness to the existing cable harness.

49
IMG-345857
 

Route the cable harness to the existing cable harness.

Install the cable.

Pull the wiring through.

50
IMG-355206
 
51
IMG-345863
 

Connect the connectors.

52
IMG-349904
 
 

Removal

53
IMG-352186
 
54
IMG-352187
 

Fold the carpet to the side.

55
IMG-353339
 

Fold the insulation to one side.

Locate the rubber grommet under the insulation and press it out.

 

Accessory installation

56
IMG-345859
 

Note!
Do not yet tighten the clamps.

Route the cable harness to the existing cable harness.

57
IMG-345860
 
 

Installation

58
IMG-353491
 

Connect the connectors.

59
IMG-349948
 
60
IMG-349942
 

Install the screws.

 

Removal

61
IMG-345877
 

Remove the clips.

Remove the screws.

62
IMG-345878
 
63
IMG-345879
 

Note!
On some markets the rubber grommet may be covered by the heat shield.

 

Accessory installation

64
IMG-345880
 

Pull the wiring through.

65
IMG-345881
 
66
IMG-353681
 

Caution!
Take extra care when handling the component.

Pull the wiring through.

Use: 1161427, Low temperature grease

67
IMG-345883
 
 

Removal

68
IMG-353376
 
69
IMG-353377
 

Release the catches.

70
IMG-353378
 
71
IMG-353381
 

Disconnect the connector.

72
IMG-354328
 
73
IMG-273585
 
74
IMG-340533
 

Remove the nuts.

 

Accessory installation

75
IMG-340606
 
76
IMG-345884
 

Pull the wiring through.

77
IMG-345885
 

Caution!
Make sure to locate the wiring in such a way that any damage caused by heat or excessive wear is avoided.


Note!
Do not yet tighten the clamps.

Route the cable harness to the existing cable harness.

78
IMG-345886
 

Note!
Do not yet tighten the clamps.

79
IMG-345887
 

Note!
Do not yet tighten the clamps.

Route the cable harness to the existing cable harness.

80
IMG-353446
 

Note!
Do not yet tighten the clamps.

Route the cable harness to the existing cable harness.

81
IMG-353447
 

Note!
Do not yet tighten the clamps.

82
IMG-345889
 
83
IMG-340544
 

Caution!
Make sure to locate the wiring in such a way that any damage caused by heat or excessive wear is avoided.

Insert the cable in to the passenger compartment, adjust the cable length out into the engine compartment and secure the rubber grommet.

84
IMG-354476
 

Caution!
Tighten clamps properly.

85
IMG-347781
 
86
IMG-347786
 
87
IMG-354996
 
88
IMG-354997
 
89
IMG-354998
 
90
IMG-354999
 

Install the screw.

91
IMG-345895
 

Connect the connector.

92
IMG-354331
 
93
IMG-336901
 

Reinstall the removed parts in reverse order.

Reinstall the battery's negative cable.

94
IMG-242268
 

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.