2017 L.H.D

Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
S60 Cross Country 2017

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313246341.031414859, 31373184
Towbar, wiring, 13-pin




Equipment
IMG-345497
IMG-239664

IMG-348782


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 
1
IMG-245980
 

  • Set the ignition key to position 0.


Note!

Wait at least one minute before unplugging the connectors or removing other electrical equipment.


 

Applies to the S60

2
IMG-339894
 

Applies to the S60

3
IMG-340180
 

4
IMG-340028
 

  • Carefully pry off the covers and remove the screws.

5
IMG-339896
 

  • Remove the panel.

6
IMG-340029
 

7
IMG-340229
 

8
IMG-340231
 

  • Remove the rubber grommet in the rear crossmember. It will not be reused.

9
IMG-340237
 

  • Take the tow hitch wiring from the kit and insert the connector in the hole in the rear crossmember.

10
IMG-340241
 

  • Adjust the cable length from the contact to the rubber grommet as illustrated.

  • Press the rubber grommet into the rear crossmember.

  • Install the contact with screws and nuts from the kit.

11
IMG-340255
 

  • Secure the cable harness at the draw bar with two cable ties.

12
IMG-361557
 

13
IMG-361552
 

  • Take the ground screw from the kit and secure the ground lead to the ground terminal on the left-hand side in the rear crossmember.

    Torque tighten the screw, tightening torque: 10 Nm (7.5 lbf.ft.).

14
IMG-361564
 

  • Install the connector.

15
IMG-361566
 

  • Clamp the cable harness to the existing cable harness using cable ties from the kit.

16
IMG-340109
 

  • Remove the cover.

17
IMG-340267
 

  • Undo the catches on both sides of the fuse holder, fold it forwards and place on the floor.

18
IMG-340349
 

  • Squeeze the locking tabs on the fuse holder lock and pull up.

19
IMG-347024
 

  • Carefully pry between the front and rear section of the fuse holder using a weatherstrip tool so that the black front section is moved to the side slightly.

  • Install the routed single cable on the rear of fuse terminal F4 in the spare socket.

  • Reinstall the catch in the rear section.

20
IMG-347025
 

21
IMG-340268
 

  • Reinstall the fuse holder.

22
IMG-340271
 

  • Install a 15 A fuse in socket F4.

23
IMG-340052
 

24
IMG-361612
 

Only applies to detachable towbar

25
IMG-340280
 

  • Saw off the corner of the panel in the cutout for the detachable towbar.

  • Even off the edges.

26
IMG-340201
 

27
IMG-339899
 

28
 

Applies to all models

  • Reinstall the detached components in reverse order.

29
IMG-348017
 


Note!

For correct function, the trailer module (TRM) must be programmed with software before checks can be carried out.


  • Checking the 13 pin connector.


Note!

To activate the trailer module (TRM) at least two light sources (lamps) must be connected. This can be done by connecting test equipment for the trailer connector or a trailer.


    Position - Function

  1. Left-hand indicator

  2. Rear fog lamps

  3. Ground terminal

  4. Right-hand indicator

  5. Right parking lamps

  6. Brake lamp

  7. Left parking lamps

  8. Reversing lamp

  9. Battery voltage, constant

  10. Battery voltage, ignition on

  11. Ground terminal

  12. Not connected.

  13. Ground terminal

30
IMG-342225
 

Applies to the V60

31
IMG-342227
 

32
IMG-340229
 

33
IMG-342235
 

  • Remove the rubber grommet in the rear crossmember. It will not be reused.

34
IMG-340237
 

  • Take the tow hitch wiring from the kit and insert the connector in the hole in the rear crossmember.

35
IMG-340241
 

  • Adjust the cable length from the contact to the rubber grommet as illustrated.

  • Press the rubber grommet into the rear crossmember.

  • Install the contact with screws and nuts from the kit.

36
IMG-340255
 

  • Secure the cable harness at the draw bar with two cable ties.

37
IMG-361571
 

38
IMG-361572
 

  • Take the ground screw from the kit and secure the ground lead to the ground terminal on the left-hand side in the rear crossmember.

    Torque tighten the screw, tightening torque: 10 Nm.

39
IMG-361573
 

  • Install the connector.

40
IMG-361576
 

  • Clamp the cable harness to the existing cable harness using cable ties from the kit.

41
IMG-342228
 

  • Remove the cover.

42
IMG-342238
 

  • Undo the two retaining catches at the rear edge and on the side of the fuse holder and lift it up.

43
IMG-340349
 

  • Squeeze the locking tabs on the fuse holder lock and pull up.

44
IMG-347024
 

  • Carefully pry between the front and rear section of the fuse holder using a weatherstrip tool so that the black front section is moved to the side slightly.

  • Install the routed single cable on the rear of fuse terminal F4 in the spare socket.

  • Reinstall the catch in the rear section.

45
IMG-347025
 

46
IMG-342237
 

  • Reinstall the fuse holder.

47
IMG-342239
 

  • Install a 15 A fuse in position F4.

48
IMG-342229
 

49
 

  • Reinstall the detached components in reverse order.

50
IMG-348017
 


Note!

For correct function, the trailer module (TRM) must be programmed with software before checks can be carried out.


  • Checking the 13 pin connector.


Note!

To activate the trailer module (TRM) at least two light sources (lamps) must be connected. This can be done by connecting test equipment for the trailer connector or a trailer.


    Position - Function

  1. Left-hand indicator

  2. Rear fog lamps

  3. Ground terminal

  4. Right-hand indicator

  5. Right parking lamps

  6. Brake lamp

  7. Left parking lamps

  8. Reversing lamp

  9. Battery voltage, constant

  10. Battery voltage, ignition on

  11. Ground terminal

  12. Not connected.

  13. Ground terminal