| | |
| | IMG-217765 |
|
| | |
| | IMG-217766 |
|
| | |
| | IMG-217767 |
|
| | Undo the front screw in the mounting for the centre console. Take the bracket for the passenger compartment connector socket from the kit. Tighten it in with the previously removed screw. Position it so that it is straight and torque tighten the screw to 24 Nm (18 lbf.ft.).
|
| | IMG-217768 |
|
| | |
| | IMG-217769 |
|
| | |
| | IMG-217770 |
|
| | Press in the locking sleeve on the passenger compartment connector socket. Slide the locking sleeve as far along the connection for the passenger compartment connector socket as possible. Take a carpet knife and cut a slit in the carpet just in front of the locking sleeve. Make the cut as long as the diameter of the locking sleeve.
Note!
Do not damage any wiring and hoses under the carpet. |
|
| | IMG-341763 |
|
| | |
| | IMG-341769 |
|
| | |
| | IMG-341766 |
|
| | |
| | IMG-232589 |
|
| | |
| | IMG-340576 |
|
| | |
| | IMG-231821 |
|
| | |
| | IMG-344136 |
|
| | Applies to cars with installed engine heater Cut off the cable tie holding the cable joint at the cable harness. Detach the cable from the clips in the subframe.
|
| | IMG-344135 |
|
| | |
| | IMG-344133 |
|
| | |
| | D3601932 |
|
| | Take a junction connector, joint cable for passenger compartment connector socket and three locking sleeves form the kit. Use low temperature grease, part no. 116.14.27, to grease the O-rings on: the connector to the front engine block heater socket both connectors on the junction connector the connector to the joint cable for the passenger compartment connector socket
Note!
Do not get any grease on the surfaces of the connector. |
|
| | IMG-344086 |
|
| | Applies when fitting passenger compartment connector at the same time Take the locking sleeves from the kit. Connect the cables in accordance with the following: Cable (1) from the engine block heater Cable (2) joint cable to the passenger compartment connector socket Cable (3) from the front engine block heater socket Press the cables firmly into the junction connector and press the locking sleeves in over the cable splices.
|
| | IMG-344134 |
|
| | |
| | IMG-299003 |
|
| | |
| | IMG-341770 |
|
| | |
| | IMG-341762 |
|
| | IMG-341757 |
|
| | |
| | IMG-360196 |
|
| | |
| | IMG-341765 |
|
| | |
| | IMG-341761 |
|
| | |
| | IMG-299043 |
|
| | |
| | IMG-231839 |
|
| | |
| | IMG-299044 |
|
| | Note!
Do not get any grease on the surfaces of the connector. |
|
| | IMG-360096 |
|
| | Insert the cable in the passenger compartment, adapt the cable length so that it runs out in the engine compartment and press the rubber grommet into place. Take the grey strip clamp from the kit and tighten the radiation shield to the cable at the rubber grommet.
|
| | IMG-344287 |
|
| | |
| | IMG-340577 |
|
| | |
| | IMG-341768 |
|
| | |
| | IMG-340568 |
|
| | |
| | IMG-340573 |
|
| | |
| | IMG-232604 |
|
| | |
| | IMG-217776 |
|
| | IMG-217777 |
|
| | Illustration A Illustration B Note!
Ensure that no grease gets onto the connector surfaces. |
Connect the cable to the passenger compartment connector socket. Press a locking sleeve (from the kit) over the joint. Fold the carpet back into position and install the passenger compartment connector socket using both the screws.
|
| | IMG-234260 |
|
| | |