2015 L.H.D

Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
S60 2015
S60 (11-18) 2015 B6304T4

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313995191.030776728, 31373831
electric engine heater, 230 V, R-design




IMG-378205




Materials

Designation

Part number

Grease

1161761


Equipment
IMG-345497
IMG-239664
IMG-239660
IMG-239980

IMG-344627

IMG-378792


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Color symbols

2
IMG-363036
 

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

  1. Used for focused component, the component with which you will do something.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

 

Removal

3
IMG-351277
 
4
IMG-378803
 

Note!
Use soap solution.

Clean the Bumper Cover surface.

5
IMG-378804
 

Use the template in the installation instructions.

Cut following the dotted lines.

6
IMG-378808
 
7
IMG-378809
 

Caution!
Cut carefully to avoid unintentional damage or personal injury.

8
IMG-352021
 
9
IMG-352031
 

Remove the screws.

Remove the nuts.

10
IMG-352036
 

Fold the wing liner to one side.

 

Accessory installation

11
IMG-351436
 
12
IMG-351416
 
13
IMG-351696
 
 

Removal

14
IMG-351435
 

Remove the panel.

15
IMG-351437
 

Remove the screws.

Remove the clips.

Remove the panel.

 

Accessory installation

16
IMG-351691
 
17
IMG-351701
 

Install the screw.


Tightening torque: M6 , 10 Nm

18
IMG-343163
 

Pull the wiring through.

Install a clips onto the upper edge of the subframe.

 

Removal

19
IMG-351271
 

Note!
Close the drain cock after the coolant has drained.

Place a container under the car.

Drain the coolant.

Tighten the nipple after draining the coolant.

 

Accessory installation

20
IMG-344072
 

Install a clips onto the upper edge of the subframe.

21
IMG-231474
 

Warning!
Be prepared to collect escaping fluid.

22
IMG-231475
 

Remove the hose.

23
IMG-231476
 
24
IMG-231477
 
25
IMG-231478
 
26
IMG-231479
 

Install the hose.

27
IMG-231480
 

Install the hose.

Install the screw.

28
IMG-231481
 

Tighten the hose clamps.

29
IMG-352076
 

Caution!
No grease on contact surfaces.

Lubricate the O-ring.

Use: 1161761, Grease

30
IMG-231482
 

Install component that comes with the accessory kit.

Connect the cable.

Install the clip(s).

31
IMG-372731
 

Install the clip(s).

 

Vehicles with passenger compartment connector

32
IMG-344086
 

Connect the prerouted cables.

  1. Cable from Engine block heater

  2. Passenger Compartment Connector Cable

  3. Cable from front socket

Install the clips as illustrated.

 

Vehicles without passenger compartment connector

33
IMG-344076
 

Connect the prerouted cables.

Install the clip(s).

34
IMG-344077
 

Install the cable.

 

Installation

35
IMG-352094
 

Caution!
Do not clamp the wire onto brake line or fuel line or power steering hose, or similar.


Caution!
Make sure to locate the wiring in such a way that any damage caused by heat or excessive wear is avoided.

Clamp the cables and connectors to the existing cables to prevent noise.

Reinstall the removed parts in reverse order.

Fill with coolant and run the engine to operating temperature.

Vent the cooling system and check for leakage.

Post-fill the cooling system if necessary.