2013 L.H.D

Installatie-instructie

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
XC60 2013
XC60 (-17) 2013

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313738931.430784190
Sill decor




IMG-284607




Equipment
A0000162
J0000368
IMG-239660
IMG-239681
A0000177
IMG-251688
A0000170

IMG-285341

IMG-213320


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

1
IMG-285323
 

2
IMG-285327
 

Installation of front cradle

  • Take one of the front cradles from the kit. All cradles are marked and only fit in one place. Always start with the front cradle.

  • Remove the protective tape from the mounting tape.

3
IMG-285328
 

  • Align the front edge of the cradle with the rear edge of the joint between the sill panels. Ensure that the tape does not adhere yet. At the same time hook the cradle on the top of the sill panel.

  • Press in the middle of the pieces of mounting tape.

4
IMG-285329
 

  • Drill out the six marked holes in the cradle using a Ø 5 mm (13/64") drill bit.

  • Remove the swarf. Use a feeler gauge to remove swarf between the cradle and sill panel.

5
IMG-285330
 

  • Rivet the cradle in all holes at the sill panel.

  • Break off the hooks along the cradle.

6
IMG-285331
 

Installation of rear cradle

  • Take the rear cradle from the kit.

  • Remove the protective tape from the mounting tape at all locations.

7
IMG-285332
 

  • Align the lugs on the cradle with corresponding holes in the front cradle. Ensure that the tape does not adhere yet.

  • Hook into the sill panel's upper edge and press at the pieces of mounting tape.

8
IMG-285333
 

  • Drill out the six marked holes using a Ø 5 mm (13/64") drill bit.

  • Remove the swarf. Use a feeler gauge to remove swarf between the cradle and sill panel.

9
IMG-285334
 

  • Rivet the cradle in all holes at the sill panel.

  • Break off the hooks along the cradle.

10
IMG-302003
 


Note!

Points 10-12, which describe bonding of the sill decor, are carried out to prevent the sill decor from detaching if the lifting table lifting plates are incorrectly positioned against the door sill panel and not against the intended lifting points at the front and rear edges of the door sill. Workshop lifts that lift all away along the door sill must be used with care.


  • Clean the marked area in the groove between the mounting hooks on the cradle using isopropanol and wipe dry.

  • Repeat the procedure with the rear cradle's rear end.

11
IMG-302004
 

  • Clean the marked area on the protrusion between both mounting hooks on the front edge of the decor strip using isopropanol and wipe dry.

  • Repeat the procedure with the rear end.

12
IMG-302005
 


Note!

Work must not be carried out at temperatures above 15º C (59º F). Use the nozzle found on the adhesive tube. The bead must not be thicker than the smallest hole in the nozzle.


  • Apply a single component adhesive to the groove between both mounting hooks on the front cradle, 10 mm (25/64") from the ends of the mounting hooks.

  • Repeat the procedure with the rear cradle's rear end.

13
IMG-285335
 


Note!

Two people are required for this step.


  • Align the decor strip's notch, placed on one of the middle catches, in front of the arrow tip at the front end of the rear cradle. The catches and edge must align with the corresponding cradle.

  • Press the decor panel into the cradles. A clicking noise should be heard when the decor strip is pressed, except from the surfaces where the adhesive is applied.

  • Ensure that the entire decor strip clicks into place properly.

 
14
IMG-285336
 

  • Press the lower part of the panel towards the sill panel at the middle holes and drill through both using a Ø 5 mm (13/64") drill bit.

  • Remove any swarf.

15
IMG-285337
 

  • Rivet the panel through the two holes.

  • Repeat drilling and riveting for the two rear holes.

16
IMG-285338
 

  • Press the lower part of the panel towards the sill panel at the front holes.

  • Drill out the rear hole using a Ø 5 mm (13/64") drill bit and the front using a Ø 6 mm (15/64") drill bit.


    Note!

    Drill through the middle of the oval hole.


  • Remove any swarf.

17A
IMG-285339
17B
IMG-293863
 

Illustrations A and B


Note!

First detach the central pin from the clip by tapping it in and then pulling it out, but leave it inside the clip a few millimeters. This is done because the decor panel springs in when the clip is attached and the central pin can break off when tapped in.


  • Attach the panel in the rear hole using a pop rivet and in the front using a clip with central pin.

  • Repeat the operation on the other side.

18
 


Note!

The vehicle must not be used within two hours of carrying out the work.



Note!

Do not wash the vehicle within 72 hours of carrying out the work.


© Volvo Car CorporationSill decor- 31373893 - V1.4
volvocars.com
Lifestyle Collection
English
Zoek een dealer
Belgium

Cookies Juridische disclaimer Privacybeleid Copyright

Copyright © 2024 Volvo Cars. All rights reserved.