| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | IMG-400004 |
|
| | Caution! Attach the antenna wires using tape. Cable ties or similar must not be used. |
|
| | |
| | IMG-363036 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | IMG-394535 |
|
| | |
| | |
| | Note! The removal steps may contain installation details. |
|
| | IMG-417442 |
|
| | |
| | IMG-417448 |
|
| | |
| | IMG-417449 |
|
| | |
| | IMG-417450 |
|
| | |
| | IMG-417451 |
|
| | Remove the screw. Tightening torque: Seat belt guide, to Bracket
, 4.4 Nm
|
| | IMG-417452 |
|
| | Remove the panel. Use hands only. |
| | IMG-421985 |
|
| | |
| | IMG-421989 |
|
| | Remove the screw. Tightening torque: Panel, to D-Pillar
, 4.5 Nm
|
| | IMG-421990 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | Vehicles with sun curtain |
| | IMG-421995 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-421996 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | |
| | IMG-422010 |
|
| | |
| | Repeat the steps when removing on opposite side. |
| | IMG-414411 |
|
| | Release the lock. Repeat on the other side. Remove the marked part. Disconnect any connector(s). |
| | IMG-421982 |
|
| | Caution! Note the location of the component before removal. |
Remove the nut. Tightening torque: Buckle safety belt to body
, 48 Nm
Loosen the marked detail/details. |
| | IMG-422035 |
|
| | Caution! Make sure that the seat backrest upholstery (fold down position) is not damaged by contact with the floor! |
|
| | IMG-421983 |
|
| | |
| | IMG-422020 |
|
| | |
| | IMG-422022 |
|
| | Remove the marked part. Disconnect the connector. |
| | IMG-422025 |
|
| | |
| | IMG-422044 |
|
| | Remove the marked part. Disconnect the connectors. |
| | Vehicles with sun curtain |
| | IMG-422050 |
|
| | |
| | IMG-422025 |
|
| | |
| | IMG-422051 |
|
| | |
| | IMG-422055 |
|
| | Disconnect the connector. |
| | IMG-422060 |
|
| | Remove the marked part. Disconnect the connectors. |
| | IMG-400005 |
|
| | Replace rear Window according to service information in VIDA: Information / Repair / Removal, replacement and installation / 8 Body and interior / 84 Exterior trim components, glass, sealing strips / 843 glass and sealing strip for windscreen and rear window / Rear window |
| | IMG-412242 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
| | IMG-414575 |
|
| | |
| | IMG-414580 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
| | IMG-414585 |
|
| | Remove the screws. Remove the panel. |
| | IMG-422120 |
|
| | Caution! Make sure that the seat backrest upholstery (fold down position) is not damaged by contact with the floor! |
|
| | IMG-422294 |
|
| | |
| | IMG-411349 |
|
| | |
| | IMG-411350 |
|
| | Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304
|
| | IMG-411351 |
|
| | Tightening torque: M8
, 24 Nm
|
| | IMG-414478 |
|
| | Release the catch. Remove the marked part. |
| | IMG-414482 |
|
| | Remove the panel. Use hands only. |
| | IMG-414483 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
| | IMG-414520 |
|
| | |
| | IMG-397280 |
|
| | |
| | IMG-397244 |
|
| | |
| | IMG-397247 |
|
| | |
| | IMG-412247 |
|
| | Note! Perform the procedure one side at a time. |
Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304
Disconnect the connector. |
| | IMG-414590 |
|
| | |
| | IMG-422856 |
|
| | Disconnect the connector. |
| | IMG-422857 |
|
| | Remove the connector from its attachment. |
| | IMG-422858 |
|
| | |
| | IMG-422861 |
|
| | |
| | IMG-422871 |
|
| | |
| | IMG-422872 |
|
| | Disconnect the connector. |
| | IMG-422873 |
|
| | |
| | IMG-422874 |
|
| | |
| | Cars with automatic transmissions |
| | IMG-410487 |
|
| | |
| | IMG-383728 |
|
| | Use special tool: T9512943, L-hook
|
| | Cars with manual transmissions |
| | IMG-422900 |
|
| | Use special tool: T9997077, Jimmy bar
|
| | IMG-422901 |
|
| | Use special tool: T9997077, Jimmy bar
|
| | IMG-425187 |
|
| | Release the locks. Loosen the marked detail/details. |
| | |
| | IMG-422902 |
|
| | |
| | IMG-422903 |
|
| | |
| | IMG-422937 |
|
| | |
| | IMG-422941 |
|
| | |
| | IMG-422943 |
|
| | Disconnect the connectors. |
| | IMG-422946 |
|
| | Caution! Make sure to protect adjacent surfaces or components. |
|
| | IMG-422936 |
|
| | Remove the screws. Remove the marked part. |
| | IMG-383939 |
|
| | Disconnect the connectors. |
| | IMG-410210 |
|
| | |
| | IMG-411195 |
|
| | |
| | IMG-411216 |
|
| | |
| | IMG-411217 |
|
| | |
| | Vehicles with keyless entry |
| | IMG-424841 |
|
| | Disconnect any connector(s). |
| | |
| | IMG-411205 |
|
| | Remove the screw. Tightening torque: M8
, 24 Nm
Remove the marked part. Repeat on the other side. |
| | IMG-411220 |
|
| | Remove the marked part. Use special tool: T9997606, Sleeve
Repeat on the other side. |
| | IMG-414161 |
|
| | |
| | IMG-411322 |
|
| | Remove the clip. Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones. |
| | IMG-411355 |
|
| | |
| | IMG-410550 |
|
| | |
| | IMG-417874 |
|
| | |
| | IMG-414370 |
|
| | |
| | IMG-400000 |
|
| | Repeat the steps when removing on opposite side. |
| | |
| | IMG-423013 |
|
| | |
| | IMG-423018 |
|
| | |
| | IMG-423027 |
|
| | |
| | IMG-423029 |
|
| | Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-423030 |
|
| | Adjust the component to a horizontal position. |
| | IMG-422326 |
|
| | Position/route the cable as illustrated. Connect the connector. |
| | IMG-422330 |
|
| | |
| | IMG-422369 |
|
| | Position/route the cables as illustrated. Install the cables. Use a cable tie |
| | IMG-424036 |
|
| | Disconnect the connector. |
| | |
| | IMG-422375 |
|
| | Connect the prerouted cables. |
| | |
| | IMG-424609 |
|
| | |
| | IMG-424367 |
|
| | Depress the secondary lock. |
| | IMG-422375 |
|
| | Connect the prerouted cables. |
| | |
| | IMG-422401 |
|
| | |
| | IMG-423052 |
|
| | Attach the connector to the wiring harness. Use a cable tie |
| | IMG-422542 |
|
| | Route the wires adjacent to existing wirings. Install the cables. Use a cable tie |
| | IMG-422543 |
|
| | Route the wires adjacent to existing wirings. Install the cables. Use a cable tie |
| | IMG-423005 |
|
| | Position/route the cables as illustrated. Install the cables. Use tape |
| | IMG-422615 |
|
| | Route the wires adjacent to existing wirings. Install the cables. Use a cable tie |
| | IMG-422670 |
|
| | Caution! Attach the antenna wires using tape. Cable ties or similar must not be used. |
Connect the connector. Position/route the cable as illustrated. Install the cable. Use tape |
| | IMG-422671 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
| | IMG-422672 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
| | IMG-423007 |
|
| | Position/route the cables as illustrated. Install the cables. Use tape |
| | IMG-423008 |
|
| | Position/route the cables as illustrated. Install the cables. Use tape |
| | IMG-422723 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
| | IMG-422726 |
|
| | Fold the insulation aside. |
| | IMG-422731 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use tape |
| | IMG-422760 |
|
| | Disconnect the connector. Remove the screw. Remove the marked part. The part is not to be reused. |
| | IMG-422777 |
|
| | Install component that comes with the accessory kit. Install the screw. Tightening torque: M6
, 10 Nm
Connect the connectors. |
| | IMG-423813 |
|
| | |
| | IMG-422780 |
|
| | Install component that comes with the accessory kit. Install the screw. Tightening torque: M6
, 10 Nm
|
| | IMG-422782 |
|
| | Connect the prerouted cable. Connect the connector. |
| | IMG-422435 |
|
| | Connect the connector. Position/route the cable as illustrated. Install the cable. Use tape |
| | IMG-422440 |
|
| | Position/route the cable as illustrated. Install the cable. Use tape |
| | IMG-422463 |
|
| | Position/route the cable as illustrated. Install the cable. Use tape |
| | IMG-422466 |
|
| | Fold the insulation aside. |
| | IMG-422469 |
|
| | Position/route the cable as illustrated. Install the cable. Use tape |
| | IMG-422480 |
|
| | Remove the screw. Remove the marked part. The part is not to be reused. |
| | IMG-422481 |
|
| | Install component that comes with the accessory kit. Install the screw. Tightening torque: M6
, 10 Nm
Connect the connectors. |
| | IMG-423811 |
|
| | |
| | IMG-422510 |
|
| | Install component that comes with the accessory kit. Install the screw. Tightening torque: M6
, 10 Nm
|
| | IMG-422518 |
|
| | Connect the prerouted cable. Connect the connector. |
| | |
| | IMG-425513 |
|
| | Remove the battery's negative cable. Tightening torque: Battery cable for battery
, 6 Nm
|
| | IMG-414735 |
|
| | |
| | IMG-416273 |
|
| | Remove the nut. Fold marked part aside. |
| | IMG-416275 |
|
| | Release the catches. Fold marked part aside. |
| | IMG-389347 |
|
| | |
| | Vehicles with Alcohol Analysing Start Inhibitor |
| | IMG-425031 |
|
| | |
| | IMG-425032 |
|
| | Use special tool: T9512631, Terminal removal tool (Color code: Brown)
|
| | IMG-425034 |
|
| | Note! On some vehicles the Red/Yellow wire might be only Red. |
|
| | IMG-425035 |
|
| | |
| | IMG-425038 |
|
| | |
| | IMG-425040 |
|
| | Use special tool: T9512620, Stripping tool (for wiring)
|
| | IMG-425039 |
|
| | |
| | IMG-425037 |
|
| | |
| | IMG-425049 |
|
| | Use special tool: T9512785, Crimping tool (included in 9512669)
|
| | IMG-425051 |
|
| | Use special tool: T9512777, Hot-air gun
|
| | |
| | IMG-422621 |
|
| | Connect the prerouted cable. |
| | IMG-389348 |
|
| | Reinstall the removed part. |
| | IMG-422622 |
|
| | Install the cable. Use a cable tie |
| | IMG-416277 |
|
| | Reinstall the removed part. |
| | IMG-422785 |
|
| | Install component that comes with the accessory kit. |
| | IMG-422819 |
|
| | Route the wires adjacent to existing wirings. Install the cables. Use a cable tie |
| | IMG-424621 |
|
| | Connect the prerouted cables. BK = Black RD = Red |
| | IMG-424623 |
|
| | Depress the secondary lock. |
| | IMG-422801 |
|
| | Route the wires adjacent to existing wirings. Install the cables. Use a cable tie |
| | IMG-422791 |
|
| | |
| | IMG-422792 |
|
| | Connect the prerouted cable. Install the nut. Tightening torque: M6
, 10 Nm
|
| | IMG-422820 |
|
| | Route the wire adjacent to existing wirings. Install the cable. Use a cable tie |
| | IMG-422821 |
|
| | Position/route the cable as illustrated. |
| | IMG-422822 |
|
| | Note! Route the wiring between floor carpet and air duct. |
Position/route the cable as illustrated. |
| | IMG-413110 |
|
| | |
| | IMG-422825 |
|
| | Position/route the cable as illustrated. |
| | IMG-423062 |
|
| | Install the cable. Use a cable tie |
| | IMG-423075 |
|
| | Install the cable. Use a cable tie |
| | IMG-422980 |
|
| | Position/route the cable as illustrated. |
| | IMG-422981 |
|
| | |
| | IMG-422416 |
|
| | Tear off the excess foam tape. |
| | IMG-414040 |
|
| | |
| | |
| | IMG-414045 |
|
| | |
| | IMG-422951 |
|
| | |
| | IMG-422950 |
|
| | |
| | IMG-423077 |
|
| | |
| | |
| | IMG-422982 |
|
| | Note! Position the template so that its surfaces are aligned against the panel. |
|
| | IMG-422983 |
|
| | |
| | IMG-422984 |
|
| | Make a hole, using the tool indicated. |
| | IMG-422985 |
|
| | |
| | IMG-423276 |
|
| | Caution! The decal must face upward. |
|
| | IMG-422986 |
|
| | Install the nut. Tighten the nut. Use hands only. |
| | IMG-422988 |
|
| | Connect the prerouted cable. |
| | IMG-423267 |
|
| | Caution! Observe caution when carrying out this step. |
Caution! The upper edge of the panel must be put in place first. |
|
| | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number. |
| | IMG-422420 |
|
| | Place the manual for this accessory in a suitable location in the car. |
| | |
| | IMG-400000 |
|
| | Reinstall the removed parts in reverse order. |
| | IMG-424469 |
|
| | |
| | IMG-424470 |
|
| | Check for correct operation. |
| | IMG-425870 |
|
| | |
| | IMG-425871 |
|
| | Caution! Make sure to carefully follow the instruction. |
Pull the component in direction of the arrow. |
| | IMG-425872 |
|
| | Caution! Make sure to place the component as the graphic shows. |
|