Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
S60 2011
S60 (11-18) 2011

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
312850881.131285083, 31339970
Parking assistance, front




 
Equipment
IMG-242205
A0000162

IMG-343371

IMG-343376


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

  

Note!

There may be components in the accessories kit that are not used for this installation.



Note!

These installation instructions apply to left-hand drive vehicles. When installing in a right-hand drive vehicle, the procedure is carried out on the opposite side and/or mirrored. Where the operation differs, right-hand versions are also displayed with text and images.


 
1
IMG-332193
 

  • Set the ignition key to position 0.


Note!

Wait at least one minute before unplugging the connector or removing other electrical equipment.


2
IMG-340600
 

  • Remove the panel.

3
IMG-308353
 

  • Disconnect any connector(s).

4
IMG-308354
 

  • Remove the sealing strip.

5
IMG-286863
 


Caution!

The front and upper sill panel must be removed and installed as one unit.


6
IMG-308355
 

7
IMG-308356
 

8
IMG-269484
 

  • Fold the carpet to one side.

9
IMG-307603
 

  • Locate the rubber grommet under the thick insulation mat and press it outwards.


Note!

Position a long tool sleeve between the body and insulation to facilitate cable routing later on.


10
IMG-341901
 

Applies to both sides

11
IMG-341902
 

Applies to vehicles rear seat heating

  • Disconnect the connector. Applies to both sides.

12
IMG-341903
 

Applies to all vehicles

13
IMG-341904
 

14
IMG-341905
 

15
IMG-341906
 

  • Remove the rear sill panel.

  • RHD: Applies to both sides.

16
IMG-307605
 

  • Remove the sealing strips.

17
IMG-307606
 

  • Detach the panel.

18
IMG-307607
 

  • Detach the panel.

19
IMG-341907
 

20
IMG-341908
 

  • Remove the nuts.

21
IMG-341910
 

  • Remove the clips.

22
IMG-341909
 

23
IMG-341912
 

24
IMG-341913
 

25
IMG-341914
 

  • Fold the wing liner out of the way.

26
IMG-341915
 

Applies to vehicles with headlamp washing

  • Release the lock and tape the hose high up on the washer fluid container to prevent washer fluid from running out.

  • Release the lock and take a piece of washer hose. Tie a knot in it and install on the washer pump to prevent the washer fluid container from emptying.

27
IMG-341916
 

Applies to all vehicles

28
IMG-341917
 

29
IMG-341918
 

  • Fold the wing liner out of the way.

30
IMG-341923
 

  • Locate the connector.

31
IMG-307686
 

  • Unplug the connector.

32
IMG-307687
 

  • RHD: Carry out this procedure on the opposite side.

33
IMG-307688
 

  • RHD: Carry out this procedure on the opposite side.

34
IMG-341924
 

35
IMG-341927
 

  • Remove the clips.

36
IMG-341931
 

  • Remove the clips.

  • Remove the screws.

37
IMG-341932
 

38
IMG-341933
 

  • Remove the clips.

39
IMG-341934
 

40
IMG-341935
 

  • Repeat the operation on the other side.

41
IMG-341936
 

42
IMG-341937
 

43
IMG-341938
 

44
IMG-341939
 

45
IMG-343381
 

46
IMG-343382
 

Applies to vehicles with chrome ring

47
IMG-343383
 

Applies to all vehicles

48
IMG-343384
 

49
IMG-343385
 

Applies to vehicles with chrome ring

50
IMG-343386
 

Applies to all vehicles

51
IMG-341944
 

  • RHD: Mirror the position of the cable harness.

52
IMG-341945
 

53
IMG-341947
 

54
IMG-343387
 

55
IMG-341948
 

Applies to left-hand drive vehicles

56
IMG-343388
 

57
IMG-341950
 

58
IMG-341961
 

Applies to left-hand drive vehicles

59
IMG-307882
 

60
IMG-341962
 

Applies to right-hand drive vehicles

61
IMG-341963
 

62
IMG-341964
 

Applies to all vehicles

  • Reinstall the bumper cover so that the hooks fasten under the headlamps.

63
IMG-341965
 

Applies to left-hand drive vehicles

  • Attach the bumper cover in reverse order.

64
IMG-341966
 

Applies to right-hand drive vehicles

65
IMG-341967
 

  • Attach the bumper cover in reverse order.

66
IMG-307909
 

Applies to left-hand drive vehicles

  • Route the cable harness at the existing cable harness.


Caution!

Make sure that the cable is positioned so that it is not damaged by heat or wear.


  • Reinstall the headlamp.

67
IMG-273585
 

Applies to left-hand drive vehicles with diesel and 6-cyl engines

68
IMG-273586
 

Applies to left-hand drive vehicles

  • Remove the plastic nuts.

69A
IMG-273587
69B
IMG-273588
 

    Illustrations A and B

  • Route the cable harness behind the insulation and further down.

70
IMG-273585
 

Applies to right-hand drive vehicles with diesel and 6-cyl engines

71
IMG-307910
 

Applies to right-hand drive vehicles

  • Route the cable harness from the headlamp and around the air filter housing.

72
IMG-307911
 

73
IMG-307912
 

  • Route the cable harness by the battery box, along towards the insulation for the cowl panel and further down.


Caution!

Make sure that the cable is positioned so that it is not damaged by heat or wear.


  • Reinstall the headlamp.

74
IMG-307913
 

  • Route the cable harness inside the insulation and further down under the car.

75
IMG-307914
 

  • Raise the car.

  • Route the cable harness down further.

76
IMG-341971
 

Applies to all vehicles

  • Raise the car.

  • Locate the hole for the rubber grommet on the cowl panel.


Note!

On certain models this may be covered by the heat insulation.


77
IMG-341973
 

  • Cut off a small rubber nipple. Lubricate the cable harness using soap solution and thread through.

  • Route the cable harness into the passenger compartment. Adjust the length.

  • Install the rubber grommet and move the heat shield on the cable harness towards the rubber grommet.

  • Reinstall the engine splash guard.

  • Lower the car.

  • Reinstall the engine cover.

78
J3703487
 

Applies to left-hand drive vehicles

  • Take the cable harness (F) connector and connect the terminals in the connector:

  • 1 Blue (BL)

    2 Green (GN)

    3 Violet (VO)

    4 Yellow (Y)

    5 White (W)

    6 Black (SB)

  • Slide the connector's catch back.

79
IMG-249180
 

Applies to right-hand drive vehicles

  • Take the cable harness (F) connector and connect the terminals in the connector:

  • 1 Blue (BL)

    2 Black (SB)

    3 Violet (VO)

    4 White (W)

    5 Yellow (Y)

    6 Green (GN)

  • Slide the connector's catch back.

80
IMG-341974
 

Applies to all vehicles

81
IMG-249181
 

  • Place the connector in the holder.

82
IMG-341975
 

83
IMG-308083
 

Applies to right-hand drive vehicles

84
IMG-308084
 

Applies to all vehicles

85
IMG-341976
 

86
IMG-343391
 


Note!

On certain vehicles there is already a connector connected in the centre outlet. Disconnect this and tape it to the existing cable harness.


87
IMG-343396
 

  • Secure extra cable length with cable ties.

88
IMG-242268
 

  • Download software (application) for the accessory's function according to service information in VIDA. See VIDA or accessories catalogue for article number on software.