Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
S60 2011
S60 (11-18) 2011

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
312960831.531414652, 31414651, 31414096, 31359260, 31414095, 31373136, 31373135, 31359259, 31316412, 31285080
Parking assistance, camera, rear




IMG-339929




 
Equipment
IMG-242205
IMG-345497
IMG-239664
IMG-239660
IMG-240673
IMG-239981
IMG-239667
IMG-351622

IMG-352091

IMG-352087


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

  

Note!

The accessories kit can contain parts that are not used.



Note!

Work is carried out the same way on left-hand drive vehicles and on right-hand drive vehicles. Left-hand drive vehicle shown. In cases where there are differences between left and right-hand drive vehicles, both versions are shown.


 
1
IMG-352121
 

2
IMG-352126
 

  • Remove the screws.

    Tightening torque: Front seat to body, 40 Nm.

3
IMG-352127
 

4
IMG-352131
 

  • Remove the screws.

    Tightening torque: Front seat to body, 40 Nm

5
IMG-340010
 

  • Open the boot lid.

6
IMG-332193
 

  • Set the ignition key to position 0.


Note!

Wait at least one minute before unplugging the connectors or removing other electrical equipment.


7
IMG-292804
 

  • Remove the panel.

8
IMG-292826
 

  • Remove the panel.

9
IMG-345113
 

  • Carefully pry loose the panel with air blower at the lower edge and then all the way around. The panel is secured by clips on the sides and at the top and with catches on the lower edge.

10
IMG-339997
 

  • Pull out the panel and disconnect the connector for the hazard warning lights.

11
IMG-339998
 

  • Remove the screws.

12
IMG-339999
 

  • Remove the screws.

13
IMG-282533
 

  • Fold the floor mat to one side by the left-hand side of the tunnel console.

14
IMG-340192
 

  • Loosen the clips on the cable harness from the tunnel console.

  • Disconnect the connector for the CCM.

15
IMG-296139
 

16
IMG-296140
 

Applies to vehicles with an automatic gearbox

  • Release the shift-lock function.

  • Move the gear selector to position "D".

17
IMG-282545
 

Applies to all models

18A
IMG-340001
18B
IMG-340196
 

Illustrations A and B

  • Carefully pry off the centre console panel starting on both sides at the rear edge. It is secured by two clips along the long sides. On manual gearboxes, the gear lever boot is secured by four catches (1) around the gear lever panel, (Image B).

  • Lift it up slightly and make sure that all cables are free from the gear lever carrier and components in the tunnel console, and lift it out.

19A
IMG-345114
19B
IMG-360002
19C
IMG-360001
19D
IMG-345115
 

Illustration A, B, C and D

  • Carefully pry off the panel at the lower edge and then all the way around.

Use: Electrician's screwdriver

20
IMG-345232
 

  • Remove the screws.

21
IMG-345233
 

  • Carefully pull the media player out, disconnect the connectors and place to one side.

22
IMG-340008
 

Illustrations A and B

23
IMG-348526
 

Applies to vehicles with 5" display


Note!

If the connection on the display is missing, the display must be changed.


24
IMG-352166
 

Applies to vehicles with 7" display

  • In cases where a connector is connected to the designated position, loosen the connector and fold back the cable and secure the connector to the existing cable harness.

    Use: Electrical tape.

25
IMG-345776
 

Applies to all models


Note!

The number of connectors, cables and cable ties can vary depending on the vehicle's equipment level.


  • Unplug the connectors.

26
IMG-341683
 

  • Carefully separate the cable duct.

27
IMG-340012
 

28
IMG-340016
 

29
IMG-340017
 

30
IMG-340018
 

31
IMG-339904
 

32
IMG-340019
 

33
IMG-340020
 

  • Disconnect the connector for the lid opener.

34
IMG-340021
 

  • Remove the panel and place to one side, new one in the kit.

35
IMG-352093
 

  • Carry out on both sides.

    Use: Screwdriver.

36
IMG-339894
 

37
IMG-340022
 

38
IMG-303083
 

39
IMG-340026
 

40
IMG-340028
 

41
IMG-339896
 

42
IMG-340029
 

43
IMG-339918
 

44
IMG-340032
 

45
IMG-340033
 

  • Remove the rubber strip.

46
IMG-340034
 

  • Carefully pull off the panel in the middle.

47
IMG-340035
 

  • Unhook the panel from the lower edge of the A-pillar panel.


Note!

Fold to one side from the bonnet opener.


48
IMG-340036
 

  • Carefully pry off the rear panel, and remove both panel sections.

49
IMG-340037
 

  • Push holes into the carpet for the locating holes for the control module bracket. Holes to the bracket are in the member. Enlarge the holes so the locating lugs go through.

50
IMG-339901
 

  • Press the bracket's locating lugs into the holes.

  • Drill through the bracket and carpet.

  • Remove bracket.

51
IMG-339903
 

  • Fold the carpet up.

  • Drill out the holes from both sides.

  • Remove any swarf.

52
IMG-340038
 

  • Rivet the nuts.

53
IMG-340039
 

  • Take the panel, camera and screws from the kit and secure the camera.

54
IMG-340040
 

  • Take the cable harness (A) from the kit and route through the hole in the boot lid.

55
IMG-340041
 

  • Connect the connector to the camera.

  • Press the contact in the other end of the cable in the supplied isolator so that it locks.

  • Press the grey lock into the isolator.

56
IMG-340057
 

57A
IMG-339906
57B
IMG-340253
 

Illustrations A and B

  • Clamp the cable from the camera at the existing cable harness along the boot lid and its swing arm using cable ties.

58
IMG-339900
 

  • Connect the connector for the lid opener to the new panel.

59
IMG-341685
 

  • Assemble the cable duct. Ensure that all catches engage.

60
IMG-339909
 

  • Continue to route the cable at the rear edge of the fuse holder down to the floor, along the existing cable harness and cable duct forward in the car under the insulation. Secure using cable ties.

61
IMG-339907
 

  • Route the cable under the insulation at the rear seat and at the cable duct and out along the left-hand rear door.

62
IMG-340254
 

  • Route the cable inside the lower B-pillar panel and carpet to the carpet joint at the left-hand front door.

63
IMG-339908
 

  • Route the existing cable (1) to the control module's power supply (under the carpet) and place it in the hole in the carpet.

  • Take the remaining cable harness (B), place it in the hole in the carpet. Route under the carpet up towards the hole for the display.

64
IMG-340115
 

  • Continue to route the cable inside the centre console and up to the location for the display. If necessary, use a piece of curtain wire to pull the cable through. Route the cable between both air ducts. Ensure that the cables are routed so they are not at risk of being cut off.

65
IMG-340256
 

  • Ensure that all cables are placed in the hole in the carpet, and allow a 350 mm piece to protrude from it.

66
IMG-340257
 

  • Tighten the control module to the bracket.

67
IMG-329273
 

68
IMG-340259
 

  • Connect the connectors to the control module.

69
IMG-329275
 

  • Clamp down the cables.

70
IMG-329276
 

71
IMG-367232
 

Check that the cable harness does not hang and touch the newly installed control module.

72
IMG-367234
 

Push up and secure the cable harness as necessary.

73
IMG-342116
 

74
IMG-342121
 

75
IMG-268064
 

76
IMG-348748
 

Illustrations A and B


Note!

The number of connectors, cables and cable ties can vary depending on the vehicle's equipment level.


  • Connect the connectors.

77
IMG-351626
 

  • Connect the newly routed cable to the display.

78
IMG-340130
 

  • Install the display and tighten.

79
IMG-340131
 

80A
IMG-340147
80B
IMG-340148
 

Illustrations A and B

  • Connect, reinstall and tighten the media player.

81
IMG-340564
 

  • Disconnect the connector from the dashboard environment panel.

82A
IMG-340580
82B
IMG-340554
 

Illustrations A and B

  • Remove the screws holding the dashboard environment panel.

  • Remove the dashboard environment panel.

83
IMG-340700
 

  • Carefully pry off the dummy.

84
IMG-340711
 

  • Take the button from the kit and push it into place instead of the dummy.

85A
IMG-340555
85B
IMG-340580
 

Illustrations A and B

86
IMG-340563
 

87
IMG-340149
 

  • Connect the connector to the CCM.

88
IMG-340150
 

89
IMG-340151
 

90
IMG-339905
 

91
IMG-340288
 

92
IMG-340152
 

93
IMG-340153
 

94
IMG-339916
 

95
IMG-339899
 

  • Reinstall loose parts in the rear seat and cargo compartment in reverse order. Torque tighten as illustrated.

96
IMG-242268
 

  • Download software (application) for the accessory's function according to service information in VIDA. See VIDA or accessories catalogue for article number on software.

97
IMG-275777
 

  • Calibrate the camera. Information can be found in VIDA under:

  • DIAGNOSTICS

    VEHICLE COMMUNICATION

    Advanced

    PAC

    Service calibration, parking camera