2012 L.H.D

Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
C70 2012
C70 (06-) 2012

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
312694391.231269434, 31269433, 31269432, 31269431
Protective plate, beneath the engine




IMG-328898




Equipment
A0000162
IMG-304663
IMG-239664
IMG-239660
IMG-304523
A0800088
A0800094

IMG-327909

IMG-213320


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 
1
IMG-327913
 

Applies to all models

  • Remove the screws for the engine splash guard and remove it.

  • The two screws (1) will be reused, place the others to one side.

2
IMG-327914
 

  • Remove the five clips in the subframe and bracket for the radiator. They will not be reused.

3
IMG-327915
 

Applies to cars with 5-cylinder diesel engine

  • Remove the two screws that hold the panel at the front edge of the right-hand inner wing.

  • Remove the panel, it will not be reused, nor the rear screw.

  • Reinstall the front screw in the inner wing.

4
IMG-327916
 

Applies to all cars with 5 Cyl. engines

  • Position three thin pieces of wood, plastic or metal on the inside of the radiator bracket. One opposite the hole in the centre and one above the hole to the right. Place the third piece to the left of the left-hand hole. This is to protect components in the connection to the radiator bracket when drilling holes.

5
IMG-327917
 

  • Cover the underneath of the engine with cardboard or similar, so that drilling swarf does not blow up into the engine compartment.


    Note!

    Do not drill out the front hole to the left. A new hole will be drilled to the side of it later.


  • Carefully drill out the four holes where the clips were located. Use tool P/N 9814112.

  • File down the edges of the holes.

  • Remove any swarf.


    Note!

    Rustproof the hole edges thoroughly.


  • Remove the cover from under the engine.

6
IMG-327928
 

  • Rivet the nuts in the drilled holes. Use tool part no. 9512782.

7
IMG-327929
 

  • Install the new protective plate for marking and drilling holes for the left front mounting.

  • At final attachment stage of the protective plate, the two screws must have two spacer washers each between the mounting lugs and the subframe. This is not required at this stage.

8
IMG-327930
 

  • Take a Ø 8.5 mm (21/64 ") drill bit and drill through the hole in the engine's protective plate and through the bracket for the radiator.

  • Remove the engine splash guard.

9
IMG-327931
 

  • Cover the underneath of the engine opposite the last hole with cardboard or similar, so that drilling swarf does not blow up into the engine compartment.

  • Carefully drill out the last hole. Use tool P/N 9814112.

  • File down the edge of the hole.

  • Remove any swarf.


    Note!

    Rustproof the hole edge thoroughly.


  • Remove the cover from under the engine.

10
IMG-327932
 

  • Rivet the nut in the drilled hole. Use tool part no. 9512782.

  • Remove the three pieces of wood, plastic or metal from the inside of the radiator bracket.

11A
IMG-327933
11B
IMG-327934
 

Illustrations A and B

  • Install the engine splash guard using two existing screws and the five screws with washers from the kit according to the diagram.


Note!

The two rear screws must have two spacer washers each between the mounting lug and the subframe. See image B.


12
IMG-327935
 

  • Torque tighten the M8 screws.

13
IMG-327936
 

Applies to cars with 4 Cyl. engines

  • Remove the screws for the engine splash guard and remove it.

  • The two screws (1) will be reused, place the others to one side.

14
IMG-327938
 

  • Remove the five clips in the subframe and bracket for the radiator. They will not be reused.

15
IMG-327939
 

  • Remove the screws at the rear edge of the inner wings on both sides.

16A
J8601084
16B
J8903376
 

Illustration A

  • Remove the covers for the nozzles for the headlamp washers on the right and left-hand sides. Carefully grip the cover. Pull the cover out until the catch becomes accessible.

Illustration B

  • Press the catch up. Remove the cover. Do not damage the painted surfaces or the washer nozzles.

17
IMG-327943
 

    Only applies to the C30

  • Apply a piece of tape to the panel of the wing edge to protect it.

  • Carefully pry off the corner of the bumper cover using a weatherstrip tool until the three hooks on the inside release.

  • Repeat the operation on the other side.

18A
IMG-327944
18B
IMG-327945
18C
IMG-327946
 

Illustration A

  • Pull the bumper cover at the lower edge slightly to access the locating lugs on top of the radiator.

  • Cut off the two locating lugs where the two first holes are to be drilled.

  • Reinstall the bumper cover.

Illustration B

  • Image B shows cutting on the right-hand side.

Illustration C

  • Image C shows cutting on the left-hand side.

19
IMG-327947
 

  • Cover the underneath of the engine at the rear edge with cardboard or similar, so that drilling swarf does not blow up into the engine compartment.

  • Carefully drill out the two holes at the rear edge where the clips were located. Use tool P/N 9814112.

  • File down the edges of the holes.

  • Remove any swarf.


    Note!

    Rustproof the hole edges thoroughly.


  • Remove the cover from under the engine.

20
IMG-327948
 

  • Rivet the nuts in the drilled holes. Use tool part no. 9512782.

21
IMG-327949
 

  • Measure the centre line between both rectangles where the old engine splash guard centre front screw was and make a cross marking.

22
IMG-327950
 

  • Make a longitudinal marking 8.5 mm (21/64 ") from the front edge and on the radiator bracket opposite where the locating lug was cut off.

  • Do the same on the other side where the other locating lug was cut off.

23A
IMG-327951
23B
IMG-327952
 

Illustrations A and B

  • Take workshop lift part no. 9985972 and fixture part no. 9995972 and use it as a support when handling the engine splash guard in the following points.

  • Position the engine splash guard on the lift and raise it towards the subframe.

  • Secure it in the two rear holes using screws and washers from the kit. One washer under the screw head and two washers between the panel and the subframe for each mounting.

    Do not tighten too hard as the engine splash guard must be adjusted at the front edge according to the made markings.

24A
IMG-327953
24B
IMG-327954
24C
IMG-327955
 

Illustration A

  • Centre the engine splash guard's two front mounting holes and the centre hole above the made markings.

  • Press up the workshop lift slightly so that the panel does not rub.

Illustrations B and C

  • Now take a loose drill bit with the same diameter as the holes in the front mounting holes and rotate to create a marking on the longitudinal markings.


    Note!

    take care when marking the two front hole. Drill the large holes on the narrow panel edge.


  • Remove the engine splash guard after marking.

  • Image B shows the left front and the centre mounting hole.

  • Image C shows both right-hand front mounting holes.

25A
IMG-327964
25B
IMG-327966
 

Illustrations A and B


Note!

Use a smooth drill bit head and ensure that the drill bit does not slip off the surface to be drilled, the surface is small in relation to the completed size of the hole.


  • Make a clear punch mark in the centre of the marking for both front holes.

  • Cover part of the underneath of engine compartment to prevent swarf from being blown up.

  • Pre-drill with a 4 mm (5/32 ") drill bit, then a 8 mm 5/16 ") drill bit and finally with drill bit part no. 9814112. Use a drill stop to prevent drilling through parts above.

  • Remove any swarf.


    Note!

    Rustproof the hole edges thoroughly and as well any scriber markings.


  • Remove the cover from under the engine.

  • Illustration A applies to the left-hand hole.

  • Illustration B applies to the right-hand hole.

26
IMG-327967
 

  • Rivet the nuts in the drilled holes. Use tool part no. 9512782.

27
IMG-327969
 

  • Install the new protective plate for marking and drilling the three holes in the mounting.

    At final attachment stage of the protective plate, the two screws must have two spacer washers each between the mounting lugs and the subframe. This is not required at this stage.

28
IMG-327970
 

  • Take a drill bit with the same diameter as the three holes in the engine splash guard. Use a drill stop.

  • Carefully drill out the three holes through the holes in the engine splash guard and radiator bracket.

  • Remove the engine splash guard.

29
IMG-327971
 

  • Install the cover beneath the engine.

  • Take drill bit part no. 9814112 and carefully drill out the three holes.

  • File down the edges of the holes.

  • Remove any swarf.


    Note!

    Rustproof the hole edges thoroughly and as well any scriber markings.


  • Remove the cover from under the engine.

30
IMG-327972
 

  • Rivet the nuts in the drilled holes. Use tool part no. 9512782.

31A
IMG-327973
31B
IMG-327974
 

Illustrations A and B

  • Install the engine splash guard using two existing screws and the seven screws with washers from the kit according to the diagram.


Note!

The two rear screws must have two spacer washers each between the mounting lug and the subframe. See image B.


32
IMG-327975
 

  • Torque tighten the M8 screws.

33
IMG-327976
 

Applies to the C30

34
IMG-327977
 

Applies to all models

35
IMG-327978