Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

There may be parts in the accessories kit that are not needed for this installation.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

7. Used for accessory components.

Removal

Remove the panel.

Disconnect the connector, if applicable.

Remove the panel.

Remove the panel.

Remove the panel.

Fold the carpet aside.

Remove the screw.

The item is not to be reused.

Remove the marked part.

Fold the floor carpet back.

Reinstall the removed part.

Take the template from the kit and cut it out following the dotted line.

Mark using a pen

Remove the panel.

Fold the carpet aside.

Fold the insulation aside.

Remove the marked detail/details.

Use: Pliers 31423632

Repeat on the other side.

Remove the screws.

Remove the marked part.

Repeat on the other side.

Remove the screws.

Remove the nuts.

Remove the clips.

Remove the screws.

Remove the clip.

Remove the marked part.

Open the hood.

Raise the car.

Remove the clips.

Remove the screws.

Remove the marked part.

Remove the screws.

Remove the clips.

Remove the screws.

Loosen the component indicated. Do not remove it.

Applies to the left-hand side:

1. Remove the connector from its attachment.

2. Remove the cable harness clips.

3. Remove the hose.

Applies to the right-hand side

1. Remove the cable harness clips.

2. Remove the hose.

Remove the marked part.

Drain the cooling system according to service information in VIDA:

Information / Repair / Cleaning, Inspection and Adjustment / 2 Engine with mountings and equipment / 26 Cooling system / 261 radiator and connections / Cooling system – draining, charging and bleeding.

Use special tool: T9997669, Key

Accessory installation

Locate relevant marking.

Saw in a way so that the marking remains.

Use: Air-powered air saw

Install component that comes with the accessory kit.

Check that the flange of the part is in full contact with bumper cover.

Adjust the hole with a file or knife as necessary.

Install components that come with the accessory kit.

Install components that come with the accessory kit.

Install component that comes with the accessory kit.

This is used as a counterhold.

Tighten the nut.

Use hands only.

Ground connection

Remove the nut.

The item is to be reused.

Position/route the cable as illustrated.

Connect the prerouted cable.

Install the nut.

Tightening torque: M6 , 10 Nm

Position/route the cables as illustrated.

Install the cables.

Use a cable tie

Lubricate the O-ring.

Install the marked component.

Install the catch.

1. Passenger Compartment Connector Cable

2. Cable from Engine block heater

Install components that come with the accessory kit.

1. Passenger Compartment Connector Cable

2. Cable from Engine block heater

Place the cable tie as illustrated.

Tighten the cable tie.

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Hold the component in the position in which it is to be fitted and mark the hoses where they are to be cut.

Assemble components that come with the accessory kit.

Adjust the position of the component according to image.

Tighten the screw.

Tightening torque: M6 , 10 Nm

Remove the screw.

The item is to be reused.

1. Fold marked part aside.

2. Install the marked components.

3. Reinstall the screw.

Attach the hose clamp

Install the hoses.

Tighten the hose clamps.

Lubricate the O-ring.

Connect the cable.

Install the catch.

Passenger Compartment Connector Cable

Position/route the cable as illustrated.

Place the cable tie as illustrated.

Position/route the cable as illustrated.

Tighten the cable tie.

Fasten the clamp.

Position/route the cable as illustrated.

Place the cable tie as illustrated.

Position/route the cable as illustrated.

Tighten the cable tie.

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Removal

Remove the clip.

Remove the screw.

Remove the nuts.

Fold the wing liner aside.

Remove the marked part.

Remove the nut.

Fold the insulation aside.

Make a cut in the insulation.

Remove the marked part.

The part is not to be reused.

Accessory installation

Pull the wiring through.

Use special tool: T9814204, Expander pliers

Insert the cable in to the passenger compartment, adjust the cable length out into the engine compartment and secure the rubber grommet.

Refit the insulation.

Install the nut.

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

Position/route the cable as illustrated.

Reinstall the removed part.

Install components that come with the accessory kit.

Lubricate the O-ring.

Install components that come with the accessory kit.

Install components that come with the accessory kit.

Fold the floor carpet back.

Adjust and center the passenger compartment power outlet in the hole of the carpet. The purpose is to have the outlet bezel cover the carpet edge.

Adjust the hole with a file or knife as necessary.

Fold the carpet aside.

Remove the screws.

Fold marked part aside.

Tighten the screw.

Tightening torque: M6 , 10 Nm

Install the marked component.

Reinstall the screws.

Make a cut in the insulation.

Remove the insulation material.

Fold the floor carpet back.

Install component that comes with the accessory kit.

Note the position.

Installation

Fill the cooling system according to the service information in VIDA:

Information / Repair / Cleaning, Inspection and Adjustment / 2 Engine with mountings and equipment / 26 Cooling system / 261 radiator and connections / Cooling system – draining, charging and bleeding.

Use special tool: T9512955, Cover

Use special tool: T9814192, Hose

Use special tool: T9512957, Coolant Reservoir

Reinstall the removed parts in reverse order.

Tightening torque: Aluminum wheel rim to wheel hub
Stage 1: 4 Nm
Stage 2: 50 Nm
Stage 3: 140 Nm