Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Conditions

There may be parts in the accessories kit that are not needed for this installation.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Preparation

Removal

Remove the marked part.

Release the lock.

Repeat on the other side.

Remove the marked part.

1. Release the locks.

Remove the marked part.

Remove the screw.

Tightening torque: Cargo anchor, to body , 13 Nm

Remove the marked part.

1. Fold marked part aside.

2. Remove the screw.

3. 
   Tightening torque: Seat belt guide, to Bracket , 4.4 Nm
   

Remove the part carefully

Fold marked part aside.

1. Release the catch.

2. Remove the marked part.

Fold marked part aside.

Disconnect the connectors.

Remove the panel.

Remove the screws.

Remove the screws.

Detach the panel.

Disconnect the connector.

Remove the panel.

Fold the carpet aside.

Remove the screws.

Remove the panel.

Remove the panel.

Disconnect the connector, if applicable.

Disconnect the connector, if applicable.

Remove the panel.

Remove the panel.

Fold the carpet aside.

Remove the marked part.

Detach the panel.

Remove the panel.

Depress the locking device.

Remove the marked part.

Remove the nut.

Fold marked part aside.

Release the catches.

Fold marked part aside.

Accessory installation

Remove the marked part.

The part is to be reused.

Remove the terminal. Use the wire only.

Use special tool: T9512620, Stripping tool (for wiring)

Use special tool: T9512785, Crimping tool (included in 9512669)

Use special tool: T9512777, Hot-air gun

All vehicles

Install component that comes with the accessory kit.

Position/route the cable as illustrated.

Tighten the cable ties.

Position/route the cable as illustrated.

Tighten the cable ties.

Position/route the cable as illustrated.

Tighten the cable ties.

Position/route the cable as illustrated.

Tighten the cable tie.

Position/route the cable as illustrated.

Route the wire adjacent to existing wirings.

Remove the nut.

Connect the prerouted cable.

Install the nut.

Tightening torque: M6 , 10 Nm

Route the wire adjacent to existing wirings.

Tighten the cable ties.

Remove the marked part.

Depress the locking device.

Release the connector's catch.

Depress the locking device.

Remove the marked part.

Connect the cable harness terminals in the connector as follows.

Route the wire adjacent to existing wirings.

Tighten the cable ties.

Depress the locking device.

Release the connector's catch.

Release the catches.

Remove the marked part.

Connect the cable harness terminals in the connector as follows.

Preparation

Open the hood.

Removal

Remove the marked part.

Use: Electrician's screwdriver

Repeat on the other side.

Remove the nut.

Repeat on the other side.

Tightening torque: Windshield wiper arm , 28 Nm

Fold marked part aside.

Disconnect the connectors.

Loosen the clips.

On both sides.

Use special tool: T9997515, Puller

Fold marked part aside.

Repeat on the other side.

Remove the clips.

Remove the marked part.

Repeat on the other side.

Remove the marked part.

Loosen the clips.

Remove the screws.

Remove the marked part.

Remove the screws.

Remove the marked part.

Tightening torque: M6 , 10 Nm

Disconnect the connector.

Release the catches.

Remove the marked part.

Remove the nut.

Tightening torque: M6 , 10 Nm

Release the locks.

Fold marked part aside.

Release the connector's catch.

Disconnect the connector.

Loosen the nut.

Tightening torque: M8 , 24 Nm

Loosen the nuts.

Fold marked part aside.

Accessory installation

Remove the marked part.

Make a hole, using the tool indicated.

Pull the wiring through.

Use: Welding rod

Make a hole, using the tool indicated.

Pull the wiring through.

Use: Welding rod

Install component that comes with the accessory kit.

Position/route the cable harness as illustrated.

Tighten the cable ties.

Remove the cable tie(s).

Depress the locking device.

Remove the marked part.

Connect the cable harness terminals in the connector as follows.

Position/route the cable as illustrated.

Tighten the cable ties.

Position/route the cable as illustrated.

Make a hole, using the tool indicated.

Pull the wiring through.

Use: Welding rod

Connect the cable harness terminals in the connector as follows.

Install component that comes with the accessory kit.

Reinstall the removed parts in reverse order.

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.