Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
C70 2006
C70 (06-) 2006

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313460851.331407108, 31346554, 31350479, 31288762
Towbar, control module (TRM)




 
Equipment
IMG-242205
IMG-345497
IMG-332314

IMG-360021


 
  

INTRODUCTION

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

  

Note!

Some steps in these installation instructions are presented with illustration only.



Note!

When installing Velcro fasteners/tape the underlying surface must be kept at a temperature of at least +20° C (68°F).

There may be parts in the accessories kit that are not needed for this installation.


1
IMG-221940
 

  • Open the boot lid.

2
IMG-334528
 

  • Lift up the cargo compartment's divider.

3
IMG-242961
 

  • Remove the covers on each side of the divider.

4
IMG-242962
 

  • Screw out the two nuts 4 revolutions, on each side of the divider.

5
IMG-242963
 

  • Lower the divider slightly.

  • Unscrew the third nut on each side of the divider four turns.

6
IMG-334529
 

  • Lower the divider completely.

7
IMG-242964
 

  • Detach the wire frame from the clip.

8
IMG-226483
 

  • Use a cable tie or the like to lock the divider's two arms on the right and left side.

9
IMG-334530
 

  • Remove the divider by gripping the arms and lifting up.

10
IMG-334531
 

    Remove:

  • the toolbox cover.

  • the spare wheel, if present.

11
IMG-334532
 

  • Take the tools out from the toolbox.

    Remove:

  • the clip.

  • the screw.

  • the toolbox.

12
IMG-334533
 

  • Remove the three screws and the load retaining eyelets from the floor.

13
IMG-334534
 

  • Remove the cover from the trunk lid stop. Use a weatherstrip tool to pry between the cover and the stop to release the catches.

14
IMG-242966
 

  • Remove the two lamps by pressing in the two catches in the top edge using a screwdriver.

15
IMG-334535
 

    Applies to cars with emergency opening handle in the cargo compartment

  • Remove the boot lid's emergency opening handle by pressing out the pin at the eye and then unhooking the wire.

16
IMG-334536
 

  • Remove the two screws in the sill moulding.

17
IMG-334537
 

  • Remove the sill moulding by pulling it up until the clips release. Move the sill moulding to one side.

18
IMG-334538
 

  • Remove the carpet in the cargo compartment.

19
IMG-334539
 

  • Remove the rubber stop on the roof's stop bracket.

20
IMG-334540
 

  • Mark out the stop bracket for the roof in relation to the screw.

  • Remove the screw and the roof's stop bracket.

21
IMG-242968
 

  • Remove the load divider lock by using a weatherstrip tool to pry between the carpet and lock.

22
IMG-221974
 

  • Remove the screw and the load retaining eyelet on the right-hand side.

23
IMG-242969
 

  • Remove the stop brace cover.

24
IMG-242970
 

  • Mark out the stop braces for the roof in relation to the screws and nuts on the right side.

  • Remove the screw, nut and the roof's stop braces.

25
IMG-221976
 

  • Undo the four clips on the side panel.

26
IMG-359901
 

  • Remove the side panel by unhooking it from the stop lug at the front edge and the pulling outward and upward so that it releases from the sealing strip.

27
IMG-359751
 

  • Remove the nuts.

28
IMG-359754
 

  • Remove the screw.

29
IMG-359757
 

30
IMG-359756
 

31
IMG-359758
 

Installing the control module

  • Clean the marked surface on the inside of the bracket using isopropanol and wipe dry.

    Use: Isopropanol, 1161721

32
IMG-356179
 

Use: Isopropanol, 1161721 Wipe dry.

33
IMG-356181
 

34
IMG-222282
 

35
IMG-241925
 

36
IMG-356351
 

When installing Velcro tape the surface must maintain a temperature of at least +20 ° C (68°F).

37
IMG-356352
 

38
IMG-359882
 

  • Press the control module against the bracket.

39
IMG-359883
 

  • Connect the connector from the wiring to the control module.

40
IMG-359890
 

  • Locate the 2-pin gray connector that is taped to the vehicle's standard cable harness.

41
IMG-359892
 

Applies to cars with parking assistance

  • Locate the 4-pin green connector that is taped to the cable harness for park assist.

42
IMG-359894
 

Applies to cars with accessory electronic modules (AEM)

  • Locate the 4-pin green connector from the accessory electronic module (AEM) taped to the vehicle's standard cable harness.

43
IMG-359895
 

Applies to others

  • Locate the 4-pin green connector that is taped to the vehicle's standard cable harness.

44
IMG-359926
 

  • Connect the extension cable to the located connector.

45
IMG-359922
 

  • Connect the connectors from the extension wiring to the control module.

46
IMG-269603
 

Applies to cars from chassis number 40000-

  • Pull up the catch on the cover on the fuse box in the engine compartment. Pull up the cover and remove it.

47
IMG-269623
 

  • Install a 40A fuse in position 14.


    Note!

    This fuse included in the TRM kit must NOT be used.


  • Reinstall the cover.

48
 

Applies to all models

  • Reinstall the detached components in reverse order.

49
IMG-242268
 

  • Download the software (application) for the accessory's function following the service information in VIDA.

    See VIDA or the accessories catalogue for software part number.