Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Disconnecting the battery

Remove the panel.

Remove the battery's negative cable.

Removal

Remove the marked part.

Repeat on the other side.

1. Release the locks.

2. Remove the marked part.

Remove the screw.

Tightening torque: Cargo anchor, to body , 13 Nm

Remove the marked part.

1. Fold marked part aside.

2. Remove the screw.

3. 
   Tightening torque: Seat belt guide, to Bracket , 4.4 Nm
   

Remove the part carefully

Fold marked part aside.

1. Release the catch.

2. Remove the marked part.

Fold marked part aside.

Disconnect the connectors.

Accessory installation

Clean the surface.

Use: , Isopropanol

Wipe dry.

Clean the surface.

Use: , Isopropanol

Wipe dry.

Remove the protective film.

Measure

Install component that comes with the accessory kit.

Remove the protective film.

Install component that comes with the accessory kit.

Removal

Make sure that the components are not mixed up at the installation.

Remove the marked part.

Repeat on the other side.

Remove the screws.

Fold the wing liner aside.

Remove the screw.

Release the catch.

Remove the marked part.

Remove the part carefully

Repeat the steps when removing on opposite side.

Remove the screws.

Loosen the component indicated. Do not remove it.

Release the connector's catch.

Disconnect the connector.

Remove the marked part.

Accessory installation

Locate relevant marking.

Make a hole, using the tool indicated.

Apply tape to the other side, opposite the marking lines.

Use: , Masking tape

1. Mark using a pen

2. Remove the marked part.

Use: Air-powered air saw

Deburr edges

Removal

Remove the marked part.

The part is not to be reused.

Remove the nuts.

The part is to be reused.

Repeat on the other side.

Remove the marked part.

The part is not to be reused.

Remove the marked part.

Use: Interior trim remover

The part is not to be reused.

Accessory installation

Install component that comes with the accessory kit.

Install the nuts

Repeat on the other side.

Install component that comes with the accessory kit.

Repeat on the other side.

Tighten the nuts.

Tighten the screw.

Tightening torque: Tow hitch member mounting to body frame
Stage 1: 50 Nm
Stage 2: 30 Degree

Repeat on the other side.

Apply the stated Material on the marked surface.

Repeat on the other side.

Use: , Rust inhibitor

Vehicles with Twin Engine

Remove the marked part.

Applies to all other vehicles

Remove the marked part.

Vehicles with spare wheel

Remove the screw.

Remove the marked part.

All vehicles

Route the wiring harness into the passenger compartment.

Install the clip(s).

Vehicles with keyless entry

Release the catch.

Fold marked part aside.

Vehicles with Twin Engine

Position wire as illustrated.

Alternative 1

Position/route the cable as illustrated.

Fasten the wiring harness using the existing clips.

Alternative 2

Position/route the cable as illustrated.

Install the wiring harness.

All vehicles

Fasten the wiring harness using the existing clips.

Position/route the cable as illustrated.

Connect the prerouted cables.

Locate the pre-routed connectors.

Connect the connectors.

The part is to be reused.

Remove the nut.

Connect the prerouted cable.

Install the nut.

Tightening torque: M6 , 10 Nm

1. Release the lock.

2. Remove the marked part.

Install component that comes with the accessory kit.

Install component that comes with the accessory kit.

Alternative 1

Removal

Remove the marked part.

The part is not to be reused.

Use: Interior trim remover

Accessory installation

Install component that comes with the accessory kit.

Connect the prerouted cable.

Alternative 2

Removal

Remove the marked part.

The part is not to be reused.

Use: Interior trim remover

Accessory installation

Install component that comes with the accessory kit.

1. Connect the connector.

2. Connect the prerouted cable.

All vehicles

Installation

Reinstall the removed parts in reverse order.

Connecting the battery

Reinstall the battery's negative cable.

Tightening torque: Battery cable for battery , 6 Nm

Accessory installation

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.

Order and download software according to: 31435639

Check

Press the button.

Fold out the towbar.

If the components rub against each other, adjustments must be made to correct this.

1. Left indicator lamp

2. Fog tail lamps.

3. Ground connection

4. Right indicator lamp

5. Right position lamp

6. Brake light

7. Left position lamp

8. Back-up lamp

9. Battery voltage, constant

10. Battery voltage, ignition on

11. Ground connection

12. Not connected

13. Ground connection

Press the button.

Fold in the towbar.