| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
|  | | IMG-440436 |
|
| | Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components. Used for accessory components.
|
| | |
|  | | IMG-497538 |
|
| | There may be parts in the accessories kit that are not needed for this installation. |
| | |
|  | | IMG-426135 |
|
| | |
| | Disconnecting the battery |
|  | | IMG-445810 |
|
| | |
|  | | IMG-445825 |
|
| | |
|  | | IMG-445938 |
|
| | Loosen the component indicated. Do not remove it. Use: Interior trim remover
|
|  | | IMG-445939 |
|
| | Disconnect the connector. Remove the marked part. |
|  | | IMG-445943 |
|
| | Remove the battery's negative cable.
Tightening torque: Battery cable for battery
, 6 Nm
|
| | |
|  | | IMG-497738 |
|
| | Release the catches. Repeat on the other side. Remove the marked part. |
|  | | IMG-497740 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-498123 |
|
| | Release the catches. Loosen the component indicated. Do not remove it. |
|  | | IMG-498133 |
|
| | Release the catches. Repeat on the other side. Remove the marked part. |
| | |
|  | | IMG-497864 |
|
| | Caution!
Make sure that the surface is clean and free of foreign material. |
Clean the marked area. Use: , Isopropanol
|
|  | | IMG-499117 |
|
| | Note!
The graphic shows the back of the component before removal. |
|
|  | | IMG-499118 |
|
| | Lift approximately 2 mm. Remove the marked part.
|
|  | | IMG-499244 |
|
| | Note!
Do not remove the protective film. |
Place the component where indicated in the graphic. Measure |
|  | | IMG-499108 |
|
| | |
|  | | IMG-499109 |
|
| | Apply tape. Use: , Masking tape
|
|  | | IMG-499110 |
|
| | Apply a thin and even layer. Use: 1161823, Activator
|
|  | | IMG-499112 |
|
| | |
|  | | IMG-499105 |
|
| | Remove the protective film. |
|  | | IMG-499137 |
|
| | Note!
Press the component to remove any air bubbles between the window and the component. |
Allow to dry for at least 20 minutes. |
| | |
|  | | IMG-412242 |
|
| | |
|  | | IMG-453298 |
|
| | Disconnect the connector. |
|  | | IMG-414575 |
|
| | |
|  | | IMG-414580 |
|
| | Remove the panel. Disconnect the connector, if applicable. |
|  | | IMG-414585 |
|
| | Remove the screws. Remove the panel. |
|  | | IMG-491860 |
|
| | Remove the marked part. Remove the screw.
Tightening torque: Panel A-pillar
, 4.5 Nm
|
|  | | IMG-491865 |
|
| | Remove the panel. Use: Interior trim remover
|
| | |
|  | | IMG-499273 |
|
| | Caution!
Take extra care not to crease the headliner. |
Install component that comes with the accessory kit. Position/route the cable as illustrated. |
|  | | IMG-497692 |
|
| | Route the wire adjacent to existing wirings. Use: , Velcro strip
|
|  | | IMG-498482 |
|
| | Fold the insulation aside. Position/route the cables as illustrated. assemble the cables. Use: , Velcro strip
|
|  | | IMG-492231 |
|
| | |
|  | | IMG-491936 |
|
| | |
|  | | IMG-491838 |
|
| | Remove fuses. The parts are not to be reused. |
|  | | IMG-492400 |
|
| | Install components that come with the accessory kit. |
|  | | IMG-498484 |
|
| | Route the wires adjacent to existing wirings. Position the cable harness excess as illustrated. Use: , Velcro strip
|
|  | | IMG-498490 |
|
| | Connect the ground cable. Install the nut.
Tightening torque: M6
, 10 Nm
|
|  | | IMG-498514 |
|
| | Route the wires adjacent to existing wirings. Use: , Velcro strip
|
|  | | IMG-499138 |
|
| | |
|  | | IMG-499132 |
|
| | Remove the marking. Use: , Isopropanol
|
|  | | IMG-492443 |
|
| | Install component that comes with the accessory kit. Connect the connector. |
|  | | IMG-499162 |
|
| | Install component that comes with the accessory kit. |
|  | | IMG-499275 |
|
| | Caution!
Take extra care not to crease the headliner. |
Route the wire adjacent to existing wirings. Use: , Velcro strip
|
| | |
| | | IMG-445943 |
|
| | Reinstall the battery's negative cable. Tighten the nut.
Tightening torque: Battery cable for battery
, 6 Nm
|
| | |
|  | | IMG-492525 |
|
| | Download the app for the accessory according to the camera's manual Connect the app to the camera |
|  | | IMG-492531 |
|
| | Adjust the camera lens vertically so that the rear edge of the hood is visible at the bottom of the image in the app. |
| | |
| | Reinstall the removed parts in reverse order. |
