Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Removal

Set the ignition key to position I.

Remove the panel.

Fold the carpet to the side.

1. Unhook the cable harness clips.

2. Disconnect the connector.

Remove the panel.

Vehicles with the 4C system.

Disconnect the connector.

All vehicles

Remove the panel.

Disconnect the connector.

Remove the screws.

Remove the screws.

Cars with automatic transmissions

Release the shift-lock function.

All vehicles

Remove the panel.

Cars with manual transmissions

All vehicles

Remove the screws.

Remove the screws.

Adjust to the lowermost position.

Repeat on the other side.

Adjust the seat to center position so that the seat fastening bolts can be removed.

Repeat on the other side.

1. Set the ignition key to position 0.

2. Remove the battery's negative cable.

Remove the screws.

Tightening torque: ,

Remove the screws.

Tightening torque: ,

Alternative 1

Alternative 2

All vehicles

Remove the screws.

Disconnect the connector.

Disconnect the connector, if applicable.

Repeat the steps when removing on opposite side.

Accessory installation

Use: 988734, Cable tie, 750 mm

Use: 988734, Cable tie, 750 mm

Use: , Electrical tape

Thread the cable tie from the head restraint's inner mounting.

Route the cable tie inside the backrest between the upholstery's thin foam and the impact protection.

Place the component where indicated in the graphic.

Use: , Electrical tape

Pull the wiring through.

Remove the tape.

Place the component where indicated in the graphic.

The cables must be positioned in front of the head restraint's tube.

Pull the wiring through.

The image shows seat without upholstery.

Using your fingers, push the cable harness under the protective pad. After installation, the cable harness must not appear under the upholstery.

1. padding

2. Protective pad

The image shows seat without upholstery.

Route the cable harness to the existing cable harness.

Install the cable.

Remove the screw.

Install the cable.

Repeat the steps when installing accessories on opposite side.

Removal

Vehicles with headset sockets

Disconnect the connector.

All vehicles

Remove the screws.

Disconnect the connector.

Accessory installation

Install component that comes with the accessory kit.

Connect the connector.

Connect the connector.

Install the part with butyl tape.

Pull the wiring through.

Reinstall the removed part.

Remove the panel.

Locate the connector.

Disconnect the connector.

Install component that comes with the accessory kit.

Connect the connector.

Connect the connector.

Install component that comes with the accessory kit.

Connect the connector.

Install the cables.

Pull the wiring through.

Connect the connectors.

Fold the carpet to the side.

Fold the floor carpet back.

Installation

Reinstall the front seat.

Connect the cable harness.

Connect the connector.

Tighten the screw.

Connect the connector.

Repeat the steps when installing on opposite side.

Reinstall the removed parts in reverse order.

Reinstall the battery's negative cable.

Set the ignition key to position II.

Set the clock.

Place the manual for this accessory in a suitable location in the car.

Adapt the DVD player to the vehicle according to: Product specifications/Design and Function/3 Electrical system/39 Media - communication and entertainment/393 Equipment for entertainment/System for rear seat entertainment/Design