Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
V60 2012
V60 (-18) 2012

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
313303701.131330365, 31339969
Parking assistance, front, R-design




 
Equipment
IMG-242205
A0000162

IMG-349930

IMG-349931


 
  
36630

Parking assistance, front, R-design

 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Conditions

2
 

These installation instructions show installation on left hand drive cars.

When installing on right-hand drive cars, perform the procedures on the opposite side and/or mirrored.

Where the procedure differs, the right-hand version is also shown with text and image.

3
IMG-332193
 

Set the ignition key to position 0.

4
IMG-340600
 

Remove the panel.

5
IMG-308353
 
6
IMG-344927
 

Remove the weatherstrip.

7
IMG-344928
 
8
IMG-344929
 
9
IMG-344930
 
10
IMG-344451
 
11
IMG-269484
 

Fold the carpet to the side.

12
IMG-307603
 

Locate the rubber grommet under the insulation and press it out.

Facilitate cable routing by temporarily raising the floor bracket using a socket or similar.

13
IMG-341901
 

On both sides.

14
IMG-341902
 

Disconnect the connector.

On both sides.

 

All vehicles

15
IMG-341903
 
16
IMG-341905
 
17
IMG-341906
 

Remove the panel.

18
IMG-307605
 

Remove the weatherstrips.

19
IMG-307606
 

Detach the panel.

20
IMG-307607
 

Detach the panel.

21
IMG-343412
 
22
IMG-343413
 

Remove the nuts.

23
IMG-341912
 

Turn the wheel inwards.

24
IMG-341913
 

Remove the screws.

 

Vehicles with headlamp washers

25
IMG-341914
 

Fold the wing liner to one side.

26
IMG-341915
 

  1. Note!
    Tape the hose high up on the washer fluid reservoir to prevent washer fluid from coming out.

  2. Take a piece of washer hose. Tie a knot in it and place it on the washer pump to prevent the washer fluid reservoir from emptying.

 

All vehicles

27
IMG-341916
 

Turn the wheel inwards.

28
IMG-341917
 

Remove the screws.

29
IMG-341918
 

Fold the wing liner to one side.

30
IMG-341923
 

Locate the connector.

31
IMG-307686
 

Disconnect the connector.

32
IMG-307687
 

RHD: The procedure is carried out on the opposite side.

33
IMG-307688
 

RHD: The procedure is carried out on the opposite side.

34
IMG-341924
 
35
IMG-341927
 

Remove the clips.

36
IMG-341931
 

Remove the clips.

Remove the screws.

37
IMG-341932
 
38
IMG-341933
 

Remove the clips.

39
IMG-349911
 

Repeat on the other side.

40
IMG-349912
 
41
IMG-349914
 

Repeat on the other side.

42
IMG-349913
 
43
IMG-349915
 
44
IMG-349916
 
45
IMG-349918
 
46
IMG-349919
 

Repeat on the other side.

47
IMG-341944
 

RHD: The cable harness is positioned mirrored.

48
IMG-341945
 
49
IMG-341947
 
50
IMG-343387
 
 

Left hand drive vehicles

51
IMG-341948
 
 

Right-hand drive vehicles

52
IMG-343388
 
53
IMG-341950
 
 

Left hand drive vehicles

54
IMG-341961
 
55
IMG-307882
 
 

Right-hand drive vehicles

56
IMG-341962
 
57
IMG-341963
 
 

All vehicles

58
IMG-349920
 

Place the Bumper Cover in position for installation.

 

Left hand drive vehicles

59
IMG-341965
 

Connect the connectors.

 

Right-hand drive vehicles

60
IMG-341966
 

Connect the connector.

61
IMG-341967
 

Connect the connector.

 

Vehicles with headlamp washers

62
IMG-350323
 

Reinstall the removed parts in reverse order.

 

All vehicles

63
 

Reinstall the bumper.

 

Left hand drive vehicles

64
IMG-307909
 

Caution!
Make sure to locate the wiring in such a way that any damage caused by heat or excessive wear is avoided.

Route the cable harness to the existing cable harness.

Reinstall the headlamp.

65
IMG-273585
 
66
IMG-273586
 

Remove the nuts.

67
IMG-349742
 
68
IMG-273588
 
 

Right-hand drive vehicles

69
IMG-273585
 
70
IMG-307910
 
71
IMG-307911
 
72
IMG-307912
 

Caution!
Make sure to locate the wiring in such a way that any damage caused by heat or excessive wear is avoided.

73
IMG-307913
 
74
IMG-307914
 
 

All vehicles

75
IMG-341971
 

Note!
On some markets the rubber grommet may be covered by the heat shield.

76
IMG-341973
 

Pull the wiring through.

Insert the cable in to the passenger compartment, adjust the cable length out into the engine compartment and secure the rubber grommet.

 

Left hand drive vehicles

77
IMG-349927
 

Release the connector's secondary lock.

Connect the pre-routed cables to the 6-pin connector.

Depress the secondary lock.

 

Right-hand drive vehicles

78
IMG-349926
 

Release the connector's secondary lock.

Connect the pre-routed cables to the 6-pin connector.

Depress the secondary lock.

 

All vehicles

79
IMG-349928
 

Connect the connector.

80
IMG-249181
 
81
IMG-349929
 
 

Right-hand drive vehicles

82
IMG-308083
 
 

All vehicles

83
IMG-308084
 
84
IMG-346331
 
85
IMG-346347
 

Connect the connector.

86
IMG-346348
 

Note!
Extra cable length must be secured using cable ties.

87
IMG-242268
 

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.