2017 L.H.D

Installation Instruction

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
V90 Cross Country 2017
L.H.D

Instruction NoVersionPart. No.Click to download PDF-version of this Installation Instruction
314390031.231439002
Parking assistance, camera, rear




Special tools

 

999 5919 PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Tool number:999 5919

Tool description:PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Tool boards:46

 

981 4199 Torque wrench

Tool number:981 4199

Tool description:Torque wrench

Tool boards:08

 

951 2620 Stripping tool (for wiring)

Tool number:951 2620

Tool description:Stripping tool (for wiring)

Tool boards:39

 

951 2785 Crimping tool (included in 9512669)

Tool number:951 2785

Tool description:Crimping tool (included in 9512669)

Tool boards:39

 

951 2777 Hot-air gun

Tool number:951 2777

Tool description:Hot-air gun

Tool boards:08


Materials

Designation

Part number

Cable tie, 750 mm

988734

Electrical tape

Lubricant

1161150


Equipment
A0000162
IMG-239664

IMG-419536

IMG-419537


 
 

Information

1
 

  • Read through all of the instructions before starting installation.

  • Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

  • Ensure that all tools stated in the instructions are available before starting installation.

  • Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

  • In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

 

Color symbols

2
IMG-363036
 

Note!
This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps.

  1. Used for focused component, the component with which you will do something.

  2. Used as extra colors when you need to show or differentiate additional parts.

  3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

  4. Used when the component is not fully removed from the vehicle but only hung to the side.

  5. Used for standard tools and special tools.

  6. Used as background color for vehicle components.

3
IMG-394535
 
 

Removal

4
 

Note!
The removal steps may contain installation details.

5
IMG-412247
 

Note!
Perform the procedure one side at a time.


Use special tool: T9995919, PULLER (SEAL-PINION,CAM-CRANKSHAFT)B200-6304

Disconnect the connector.

6
IMG-414590
 

Remove the panel.

7
IMG-412242
 

Remove the panel.

Disconnect the connector, if applicable.

8
IMG-414575
 

Remove the panel.

9
IMG-414580
 

Remove the panel.

Disconnect the connector, if applicable.

10
IMG-414585
 

Remove the screws.

Remove the panel.

11
IMG-411070
 
12
IMG-414613
 
13
IMG-414614
 

Remove the panel.

14
IMG-414995
 
15
IMG-415046
 

Note!
The graphic shows the back of the component before removal.

16
IMG-415047
 

Remove the panel.

Use hands only.

17
IMG-415049
 

Release the catch.

Remove the marked part.

18
IMG-418522
 

Remove the panel.

Use hands only.

19
IMG-418525
 

Remove the screw.


Tightening torque: M6 , 10 Nm

20
IMG-414411
 

Release the lock.

Repeat on the other side.

Remove the marked part.

21
IMG-414483
 

Remove the panel.

Disconnect the connector, if applicable.

22
IMG-422120
 

Caution!
Make sure that the seat backrest upholstery (fold down position) is not damaged by contact with the floor!

23
IMG-422121
 
24
IMG-414520
 
25
IMG-397280
 

Remove the marked part.

26
IMG-397244
 

Detach the panel.

27
IMG-397247
 

Remove the panel.

28
IMG-383130
 

Remove the screws.


Tightening torque: Front seat to body , 40 Nm

29
IMG-414525
 
30
IMG-414515
 

Remove the screws.


Tightening torque: Front seat to body , 40 Nm

31
IMG-383134
 
32
IMG-396605
 

Disconnect the connector.

33
IMG-396606
 

Unhook the cable harness clips.

34
IMG-414526
 
35
IMG-416201
 

Remove the screws.

Fold marked part aside.

36
IMG-407110
 
37
IMG-414611
 

Remove the marked part.

38
IMG-415830
 

Repeat on the other side.

39
IMG-415831
 

Remove the screw.


Tightening torque: M6 , 10 Nm

Repeat on the other side.

40
IMG-416086
 
41
IMG-416087
 

Remove the marked part.

 

Vehicles with keyless entry

42
IMG-413321
 
 

All vehicles

43
IMG-415835
 

Remove the screws.

44
IMG-416089
 

Remove the marked part.

45
IMG-418545
 

Disconnect the connectors.

Remove the panel.

46
IMG-418696
 

Remove the screws.

47
IMG-418703
 

Note!
The graphic shows the back of the component before removal.

48
IMG-418710
 

Remove the panel.

49
IMG-418626
 

Remove the panel.

50
IMG-418631
 

Remove the panel.

51
IMG-418634
 

Remove the screws.

Remove the panel.

52
IMG-418641
 

Disconnect the connector.

53
IMG-418643
 

Loosen the screws.

Loosen the exact number of turns indicated in the image.

54
IMG-418645
 

Use: Interior trim remover

The part is not to be reused.

 

Accessory installation

55
IMG-419877
 
56
IMG-418648
 

Tighten the bolts.


Use special tool: T9814199, Torque wrench

57
IMG-418642
 

Connect the connector.

58
IMG-418825
 

Loosen the marked detail/details.

To be repeated in the other end of the component.

59
IMG-418831
 

Release the catches.

Loosen the marked detail/details.

Use: Scribe

Use: Interior trim remover

To be repeated in the other end of the component.

60
IMG-419675
 

Use: 988734, Cable tie, 750 mm

61
IMG-419680
 

Use: , Electrical tape

62
IMG-419795
 
63
IMG-419800
 

Pull the wiring through.

64
IMG-419801
 

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

65
IMG-419802
 

Turn once.

Tear off the excess foam tape.

66
IMG-419805
 

Pull the wiring through.

Use: 1161150, Lubricant

Wipe off

Remove the cable tie(s).

67
IMG-419818
 

Pull the wiring through.

68
IMG-418850
 

Reinstall the removed part.

To be repeated in the other end of the component.

69
IMG-418841
 

Caution!
Make sure that the rubber grommet seals properly to the body.

Reinstall the removed part.

To be repeated in the other end of the component.

70
IMG-418795
 

Route the wire adjacent to existing wirings.

Install the cable.

Use a cable tie

71
IMG-418722
 

Remove the marked part.

72
IMG-416273
 

Remove the nut.

Fold marked part aside.

73
IMG-416275
 

Release the catches.

Fold marked part aside.

74
IMG-389347
 

Remove the marked part.

75
IMG-389346
 
76
IMG-389348
 

Reinstall the removed part.

77
IMG-402750
 

Install the cable.

Use a cable tie

78
IMG-416277
 

Reinstall the removed part.

79
IMG-416317
 

Install component that comes with the accessory kit.

80
IMG-418790
 

Route the wires adjacent to existing wirings.

Install the cables.

Use a cable tie

81
IMG-418792
 

Route the wires adjacent to existing wirings.

Install the cables.

Use a cable tie

82
IMG-418793
 

Route the wires adjacent to existing wirings.

Install the cables.

Use a cable tie

83
IMG-416319
 

Position/route the cables as illustrated.

84
IMG-416320
 

Note!
Route the wiring between floor carpet and air duct.

Position/route the cables as illustrated.

85
IMG-415092
 

Remove the marked part.

86
IMG-415095
 

Remove the marked part.

The part is not to be reused.

87
IMG-416389
 

Fold marked part aside.

88
IMG-416390
 

Position/route the cables as illustrated.

89
IMG-419737
 

Install the cables.

Use a cable tie

90
IMG-415097
 

Position/route the cables as illustrated.

91
IMG-419700
 
92
IMG-415145
 

Install the nuts

93
IMG-415150
 
94
IMG-419740
 

Connect the prerouted cable.

Position/route the cable as illustrated.

95
IMG-419745
 

Caution!
Make sure that the wire is not bent to a radius of less than 5 mm.

Position the cable harness excess as illustrated.

Install the cable.

Use a cable tie

96
IMG-419740
 

Connect the prerouted cable.

Position/route the cable as illustrated.

97
IMG-415153
 

Connect the cable.

Position/route the cable as illustrated.

98
IMG-401401
 
99
IMG-415155
 
100
IMG-388631
 
101
IMG-388638
 

Remove the nut.

102
IMG-388639
 

Connect the prerouted cable.

Install the nut.


Tightening torque: M6 , 10 Nm

103
IMG-388633
 
104
IMG-416431
 

Fold marked part aside.

105
IMG-416445
 
  1. Release the connector's catch.

  2. Release the lock.

  3. Disconnect the connector.

106
IMG-416446
 

Release the connector's catch.

Remove the connector from its attachment.

107
IMG-416447
 

Remove the tape.

108
IMG-397975
 

Note!
Orientation view

109
IMG-416490
 
110
IMG-374930
 


Use special tool: T9512620, Stripping tool (for wiring)

111
IMG-374928
 
112
IMG-398784
 


Use special tool: T9512785, Crimping tool (included in 9512669)

113
IMG-398782
 


Use special tool: T9512785, Crimping tool (included in 9512669)

114
IMG-326808
 

Caution!
Make sure that the surrounding components are protected from heat.


Use special tool: T9512777, Hot-air gun

115
IMG-397870
 
116
IMG-416493
 

Install the connector to its attachment.

117
IMG-416498
 

Connect the connector.

118
IMG-416494
 

Caution!
Make sure that no part of the wiring harness is trapped.

Reinstall the removed part.

119
IMG-416506
 

Note!
Extra cable length must be secured using cable ties.

Position/route the cable as illustrated.

120
IMG-415166
 

Position/route the cable as illustrated.

Install the cable.

Use a cable tie

121
IMG-415238
 

Position/route the cable as illustrated.

122
IMG-415163
 

Connect the prerouted cable.

123
IMG-415239
 

Install component that comes with the accessory kit.

124
IMG-242268
 

Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number.

 

Installation

125
IMG-400000
 

Reinstall the removed parts in reverse order.