| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | When installing, the car must retain a temperature of 20 degrees C. |
| | |
| | IMG-363036 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | Disconnecting the battery |
| | IMG-430215 |
|
| | |
| | IMG-435728 |
|
| | |
| | IMG-435731 |
|
| | |
| | IMG-473728 |
|
| | Remove the battery's negative cable. |
| | |
| | IMG-435736 |
|
| | Remove the part carefully Repeat on the other side. |
| | IMG-435739 |
|
| | |
| | IMG-436415 |
|
| | |
| | IMG-437920 |
|
| | |
| | IMG-435742 |
|
| | |
| | IMG-435743 |
|
| | |
| | IMG-435744 |
|
| | |
| | IMG-435745 |
|
| | |
| | IMG-431005 |
|
| | Remove the screw. Tightening torque: Seat belt guide, to Bracket
, 4.5 Nm
|
| | IMG-435771 |
|
| | |
| | IMG-435772 |
|
| | |
| | IMG-431337 |
|
| | |
| | IMG-436490 |
|
| | Remove the marked part. Use: Interior trim remover
|
| | IMG-436500 |
|
| | Remove the screws. Tightening torque: Luggage compartment sill moulding to body
, 4.5 Nm
|
| | IMG-473324 |
|
| | |
| | IMG-436546 |
|
| | |
| | IMG-435773 |
|
| | Note! The graphic shows the back of the component before removal. |
Note! The number of connectors may vary depending on the vehicle's equipment level. |
Disconnect the connector. |
| | |
| | IMG-435779 |
|
| | Clean the surface. Wipe dry. Use: 1161721, Isopropanol
|
| | IMG-435774 |
|
| | Clean the surface. Use: 1161721, Isopropanol
Wipe dry. |
| | IMG-414059 |
|
| | |
| | IMG-241925 |
|
| | |
| | IMG-435781 |
|
| | Measure Install component that comes with the accessory kit. |
| | IMG-435784 |
|
| | Remove the protective film. |
| | IMG-435786 |
|
| | Note! Ensure that the tape is fixed to the surface. |
Install component that comes with the accessory kit. |
| | |
| | IMG-435791 |
|
| | Make sure that the components are not mixed up at the installation. Remove the marked part. |
| | IMG-435798 |
|
| | |
| | IMG-446456 |
|
| | Remove the marked detail/details. |
| | IMG-441820 |
|
| | Remove the marked detail/details. |
| | IMG-446440 |
|
| | |
| | IMG-446442 |
|
| | Remove the screws. Remove the clip. |
| | IMG-446443 |
|
| | |
| | IMG-446444 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-446445 |
|
| | Caution! Make sure not to damage painted surfaces. |
Remove the marked part. Use: Interior trim remover
|
| | IMG-446446 |
|
| | Caution! Be extra careful when removing or installing this component. |
Loosen the component indicated. Do not remove it. |
| | IMG-446447 |
|
| | Loosen the component indicated. Do not remove it. |
| | Repeat the steps when removing on opposite side. |
| | IMG-435822 |
|
| | Locate the connector. Release the connector's catch. Disconnect the connector. |
| | IMG-435823 |
|
| | Caution! Place the Bumper Cover on a suitable surface. |
Request the aid of a colleague for this procedure. Remove the marked part. |
| | IMG-435835 |
|
| | Remove the nuts. The part is not to be reused. Repeat on the other side. |
| | IMG-435836 |
|
| | Remove the marked part. The part is not to be reused. |
| | IMG-435837 |
|
| | Remove the marked part. The part is not to be reused. |
| | IMG-436021 |
|
| | |
| | IMG-436022 |
|
| | Apply tape to the other side, opposite the marking lines. Use: , Masking tape
|
| | IMG-436026 |
|
| | Mark using a pen Remove the marked part.
Use: Air-powered air saw
|
| | IMG-436027 |
|
| | |
| | |
| | IMG-435843 |
|
| | Clean the surface. Use: 1161721, Isopropanol
|
| | IMG-435845 |
|
| | Clean the surface. Use: 1161721, Isopropanol
|
| | IMG-435851 |
|
| | Install component that comes with the accessory kit. |
| | IMG-435855 |
|
| | Install components that come with the accessory kit. Tighten the bolts. Tightening torque: Tow hitch member mounting to body frame (pre-tightening)
, 30 Nm
Repeat on the other side. |
| | IMG-436044 |
|
| | Note! This step is easier with two people. |
Install component that comes with the accessory kit. |
| | IMG-435879 |
|
| | Install components that come with the accessory kit. Tighten the nuts. Tightening torque: Towbar, to Towbar member Stage 1:
90 Nm Stage 2:
60 Degree
Repeat on the other side. |
| | IMG-435895 |
|
| | Tighten the bolts. Tightening torque: Tow hitch member mounting to body frame Stage 1:
90 Nm Stage 2:
60 Degree
Repeat on the other side. |
| | IMG-436525 |
|
| | Apply the stated Material on the marked surface. Repeat on the other side. Use: , Rust inhibitor
|
| | IMG-428470 |
|
| | Install component that comes with the accessory kit. Use hands only. |
| | IMG-436028 |
|
| | Fasten the wiring harness using the existing clips. |
| | IMG-436030 |
|
| | Route the wiring harness into the passenger compartment. |
| | IMG-358177 |
|
| | Caution! Make sure that the rubber grommet seals properly to the body. |
|
| | IMG-436031 |
|
| | Fasten the wiring harness using the existing clips. |
| | IMG-436051 |
|
| | Fasten the wiring harness using the existing clips. Connect the connector. |
| | IMG-435887 |
|
| | Remove the nut. The part is to be reused. |
| | IMG-435888 |
|
| | Connect the prerouted cable. Install the nut. Tightening torque: Tow hitch ground connection, to body
, 13 Nm
|
| | IMG-436052 |
|
| | Locate the pre-routed connectors. Connect the connectors. |
| | |
| | IMG-487822 |
|
| | |
| | |
| | IMG-483349 |
|
| | |
| | IMG-483361 |
|
| | Place the component where indicated in the graphic. |
| | IMG-483362 |
|
| | Use detail according to image. Mark using a pen |
| | IMG-483377 |
|
| | Caution! Cut carefully to avoid unintentional damage or personal injury. |
Remove the marked part. |
| | IMG-483378 |
|
| | The part is not to be reused. |
| | IMG-483364 |
|
| | Reinstall the removed part. |
| | IMG-483365 |
|
| | Place the component where indicated in the graphic. |
| | |
| | IMG-483373 |
|
| | Use details according to image. |
| | IMG-437645 |
|
| | Cut following the dotted lines. |
| | IMG-241925 |
|
| | |
| | IMG-437646 |
|
| | The graphic shows the back of the component. Install component that comes with the accessory kit. |
| | IMG-241925 |
|
| | |
| | IMG-487825 |
|
| | |
| | IMG-437647 |
|
| | Caution! Make sure that no part of the wiring harness is trapped. |
Install component that comes with the accessory kit. |
| | |
| | Reinstall the removed parts in reverse order. |
| | IMG-405228 |
|
| | Tightening torque: Aluminum wheel rim to wheel hub Stage 1:
4 Nm Stage 2:
50 Nm Stage 3:
140 Nm
|
| | |
| | IMG-474019 |
|
| | Reinstall the battery's negative cable. Tightening torque: Battery cable for battery
, 6 Nm
|
| | |
| | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. Order and download software according to: 31664323
|
| | |
| | IMG-384866 |
|
| | Warning! Check for correct operation after the installation. |
Note! To activate the trailer module (TRM) at least two light sources (lamps) must be connected. This can be done by connecting test equipment for the trailer connector, or a trailer. |
Note! The trailer module (TRM) must be programmed with correct software to function correctly. |
7-pin connection Brake lamp/Left indicator Ground connection Spare slot (brake lamp, electrical trailer brake) Stop lamp/ Right turn signal lamp Charging Position lamp Spare (back-up light)
|
| | IMG-384862 |
|
| | 4-pin connection Stop lamp/ Right turn signal lamp Brake lamp/Left indicator Position lamp Ground connection
|