| | |
| | Read through all of the instructions before starting installation. Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation. Ensure that all tools stated in the instructions are available before starting installation. Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps. In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.
|
| | |
| | There may be parts in the accessories kit that are not needed for this installation. |
| | |
| | IMG-363036 |
|
| | Note! This colour chart displays (in colour print and electronic version) the importance of the different colours used in the images of the method steps. |
Used for focused component, the component with which you will do something. Used as extra colors when you need to show or differentiate additional parts. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc. Used when the component is not fully removed from the vehicle but only hung to the side. Used for standard tools and special tools. Used as background color for vehicle components.
|
| | IMG-394535 |
|
| | |
| | |
| | Note! The removal steps may contain installation details. |
|
| | IMG-394779 |
|
| | |
| | IMG-383039 |
|
| | |
| | IMG-383043 |
|
| | Tightening torque: Panel A-pillar
, 4.5 Nm
|
| | IMG-383044 |
|
| | Remove the panel. Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones. |
| | IMG-383045 |
|
| | |
| | IMG-383046 |
|
| | |
| | IMG-383040 |
|
| | |
| | IMG-394727 |
|
| | |
| | Vehicles with seven seats |
| | IMG-401374 |
|
| | |
| | IMG-424681 |
|
| | Note! The graphic shows the back of the component before removal. |
|
| | IMG-424606 |
|
| | |
| | IMG-424602 |
|
| | Remove the screw. Tightening torque: Safety belt lower anchor to body (rear)
, 40 Nm
|
| | Applies to all other vehicles |
| | IMG-383042 |
|
| | |
| | |
| | IMG-383047 |
|
| | Note! Do not loosen the bolts more than 2 turns. |
|
| | IMG-383048 |
|
| | Remove the panel. Check that the fasteners are undamaged before installation. If not, they must be replaced with new ones. |
| | IMG-383066 |
|
| | |
| | IMG-393945 |
|
| | Remove the screws. Tightening torque: Cargo anchor, to body
, 13 Nm
|
| | IMG-397295 |
|
| | |
| | IMG-383125 |
|
| | |
| | IMG-396625 |
|
| | |
| | Vehicles with air suspension |
| | IMG-398660 |
|
| | |
| | IMG-398661 |
|
| | Disconnect the connector. |
| | |
| | IMG-383049 |
|
| | Remove the panel. Disconnect the connectors. |
| | IMG-413025 |
|
| | Remove the screws. Disconnect the connector, if applicable. Remove the marked part. |
| | |
| | IMG-424386 |
|
| | Loosen the component indicated. Do not remove it. |
| | |
| | IMG-423575 |
|
| | Disconnect the connectors. |
| | IMG-423233 |
|
| | Remove the nut. Remove the screws. |
| | IMG-423234 |
|
| | Remove the marked part. The part is not to be reused. |
| | IMG-423746 |
|
| | |
| | IMG-423745 |
|
| | Remove the tape. Adjust the position of the wiring harness. |
| | |
| | IMG-412964 |
|
| | |
| | IMG-422257 |
|
| | Install component that comes with the accessory kit. |
| | IMG-423115 |
|
| | |
| | IMG-423215 |
|
| | Adjust the component to a horizontal position. |
| | IMG-422245 |
|
| | |
| | IMG-423232 |
|
| | |
| | |
| | IMG-422218 |
|
| | |
| | IMG-422219 |
|
| | |
| | IMG-422223 |
|
| | |
| | IMG-424387 |
|
| | Reinstall the removed part. |
| | |
| | IMG-422250 |
|
| | Connect the connector, if applicable. Reinstall the removed part. Reinstall the screws. |
| | |
| | IMG-422256 |
|
| | |
| | |
| | IMG-414053 |
|
| | |
| | IMG-414054 |
|
| | Position/route the cable as illustrated. Install the cable. Use a cable tie |
| | IMG-422397 |
|
| | Note! Position the template so that its surfaces are aligned against the panel. |
|
| | IMG-422398 |
|
| | Use a drill with the stated size |
| | IMG-422399 |
|
| | Use a drill with the stated size |
| | IMG-422005 |
|
| | |
| | IMG-421926 |
|
| | Note! Do not fully tighten the nut yet. |
Install the nut. |
| | IMG-421950 |
|
| | Note! Position the holder horizontally on the panel. |
Tighten the nut. Use hands only. |
| | IMG-421925 |
|
| | Connect the prerouted cable. |
| | IMG-242268 |
|
| | Download software (application) for the accessory's function according to the service information in VIDA. See VIDA or the accessories catalogue for software part number. |
| | |
| | IMG-400000 |
|
| | Reinstall the removed parts in reverse order. |
| | IMG-422420 |
|
| | Place the manual for this accessory in a suitable location in the car. |