| | |
| | IMG-352652 |
|
| | |
| | IMG-352653 |
|
| | |
| | IMG-352654 |
|
| | |
| | IMG-352653 |
|
| | |
| | IMG-352655 |
|
| | Caution!
protect the connections' contact surface against paint. |
Paint the sensors in the same colour code as the vehicle. Use Volvo Touch-up paint. (Only use base coat.) Use: Volvo 2-K Varnish. P/N: 31335447
Note!
Also read the instructions on the spray can. |
|
| | IMG-352658 |
|
| | Caution!
The paint must have dried after the first application. |
|
| | |
| | IMG-247309 |
|
| | |
| | IMG-247266 |
|
| | |
| | IMG-211568 |
|
| | |
| | IMG-247267 |
|
| | Pull the corner straight out, continue to pull the bumper cover backwards until the five clips at the upper edge release. Repeat the operation on the other side.
|
| | IMG-247268 |
|
| | |
| | |
| | IMG-352668 |
|
| | |
| | IMG-352669 |
|
| | |
| | IMG-352670 |
|
| | |
| | IMG-352671 |
|
| | Caution!
The cutting part of the tool must be on the outside of the cover. |
|
| | IMG-352672 |
|
| | |
| | IMG-352667 |
|
| | |
| | IMG-352673 |
|
| | |
| | IMG-352666 |
|
| | |
| | |
| | IMG-226907 |
|
| | |
| | IMG-226722 |
|
| | |
| | IMG-255684 |
|
| | |
| | IMG-255685 |
|
| | Unplug connector for 12V outlet, if installed. |
| | Installation of the Parking Assistance Module (PAM) |
| | IMG-247272 |
|
| | Installation of the Parking Assistance Module (PAM) |
| | IMG-247273 |
|
| | |
| | IMG-247274 |
|
| | |
| | IMG-247275 |
|
| | |
| | IMG-247276 |
|
| | |
| | IMG-247277 |
|
| | |
| | IMG-247278 |
|
| | |
| | IMG-247279 |
|
| | |
| | Reinstall: the side panels. the sill trim panel. the floor carpet. Fold up the backrest.
|
| | |
| | IMG-247283 |
|
| | |
| | IMG-247284 |
|
| | |
| | IMG-352674 |
|
| | |
| | IMG-247286 |
|
| | Install the centering tool in one holder. Install the tool on the bumper cover. Hold the holder securely when removing the centering tool. The holder must be installed horizontally and in line with the bumper cover. Repeat the steps until all four holders are in place.
|
| | IMG-247287 |
|
| | |
| | IMG-247288 |
|
| | |
| | IMG-247289 |
|
| | |
| | IMG-247290 |
|
| | Installing the bumper Lift up the bumper and connect the connector. Press the bumper's hooks in at the rear edge. Press all the hooks for the ends into the body. Reinstall the screws on the front edges of the bumper casing. Reinstall the plastic nuts at the lower edge.
|
| | |
| | IMG-236045 |
|
| | |
| | IMG-236046 |
|
| | |
| | IMG-236047 |
|
| | |
| | |
| | IMG-242268 |
|
| | |