Information

• Read through all of the instructions before starting installation.

• Notifications and warning texts are for your safety and to minimise the risk of something breaking during installation.

• Ensure that all tools stated in the instructions are available before starting installation.

• Certain steps in the instructions are only presented in the form of images. Explanatory text is also given for more complicated steps.

• In the event of any problems with the instructions or the accessory, contact your local Volvo dealer.

Further information

These installation instructions show installation on left hand drive cars.

When installing on right-hand drive cars, perform the procedures on the opposite side and/or mirrored.

Where the procedure differs, the right-hand version is also shown with text and image.

Color symbols

1. Used for focused component, the component with which you will do something.

2. Used as extra colors when you need to show or differentiate additional parts.

3. Used for attachments that are to be removed/installed. May be screws, clips, connectors, etc.

4. Used when the component is not fully removed from the vehicle but only hung to the side.

5. Used for standard tools and special tools.

6. Used as background color for vehicle components.

Paintwork

Clean the surface.

Use: 1161721, Isopropanol

Matt the surface gently.

Use: , Sand paper P1000

Clean the surface.

Use: 1161721, Isopropanol

Use: , Volvo Original Touch-up paint

Use base coat only.

Also see the instructions on the container.

Use: 31335447, Varnish 2-component

Also see the instructions on the container.

Removal

Set the ignition key to position 0.

Remove the panel.

Fold the carpet aside.

Unhook the cable harness clips.

Disconnect the connector.

Remove the panel.

Disconnect the connector, if applicable.

Disconnect the connector.

Remove the screws.

Remove the screws.

Cars with automatic transmissions

Release the shift-lock function.

All vehicles

Cars with manual transmissions

All vehicles

Disconnect the connector.

Remove the screws.

Select the first free position closest to the driver.

Left hand drive vehicles

If all locations for the switch are occupied a switch with function must be removed in priority order as illustrated.

1. BLIS

2. Distance Alert

3. Lane depature warning (LDW)

Right-hand drive vehicles

If all locations for the switch are occupied a switch with function must be removed in priority order as illustrated.

1. BLIS

2. Distance Alert

3. Lane depature warning (LDW)

All vehicles

Accessory installation

Removal

Remove the weatherstrip.

Fold the carpet aside.

Locate the rubber grommet under the insulating mat.

Fold the insulation aside.

Remove the marked part.

The part is not to be reused.

Repeat on the other side.

Disconnect the connector, if applicable.

Repeat on the other side.

Remove the panel.

Remove the weatherstrips.

Detach the panel.

Remove the nuts.

Remove the panel.

Remove the panel.

Tightening torque: Wheel to wheel hub
Stage 1: 20 Nm
Stage 2: 140 Nm

Disconnect the connector.

Accessory installation

Install component that comes with the accessory kit.

Tightening torque: M5 , 5 Nm

Connect the connector.

Removal

Remove the screws.

Vehicles with headlamp washers

Fold the wing liner aside.

1. 
   

   Note! Tape the hose high up on the washer fluid reservoir to prevent washer fluid from coming out.

   
   

2. Take a piece of washer hose. Tie a knot in it and place it on the washer pump to prevent the washer fluid reservoir from emptying.

Right-hand drive vehicles

Turn the wheel inwards.

Remove the screws.

Fold the wing liner aside.

Left hand drive vehicles

Tightening torque: Wheel to wheel hub
Stage 1: 20 Nm
Stage 2: 140 Nm

Remove the screws.

Remove the screws.

Remove the nuts.

All vehicles

Locate the connector.

1. Depress the locking device.

2. Disconnect the connector.

Remove the clips.

Remove the clips.

Remove the screws.

Remove the clip.

Remove the screws.

Remove the screws.

Remove the clips.

Repeat on the other side.

Locate the markings for the positions.

Mark the centre.

Use special tool: T9997234, Hole stamp

All vehicles

Use: 1161721, Isopropanol

Use: 1161721, Isopropanol

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

Use: 8637076, Activator

Allow to dry for at least 10 minutes.

Disconnect the connector.

Repeat on the other side.

Release the catches.

Remove the panel.

Repeat on the other side.

Release the catches.

Remove the panel.

The part is not to be reused.

Repeat on the other side.

Accessory installation

Repeat on the other side.

Reinstall the removed part.

Connect the connector.

Repeat on the other side.

Use special tool: T9512950, Glue gun (kit)

Use: 1161730, Mixing pipe
Use: 9511027, Glue

Repeat on the other side.

Put the wiring in the Bumper cover without installing the wiring.

RHD: The cable harness is positioned mirrored.

Connect the connectors.

Position/route the cable harness as illustrated.

Adjust the position of the wiring harness.

Repeat on the other side.

Left hand drive vehicles

Use: , Electrical tape

Remove the screw.

Remove the marked part.

Remove the nuts.

Use special tool: T9512932, Tension spring

Use: , Electrical tape

Pull the wiring through.

Pull the wiring through.

Right-hand drive vehicles

Use: , Electrical tape

All vehicles

Pull the wiring through.

Place the component where indicated in the graphic.

Pull the wiring through.

Position/route the cable harness as illustrated.

Position/route the cable harness as illustrated.

Right-hand drive vehicles

All vehicles

Position/route the cable harness as illustrated.

Position/route the cable harness as illustrated.

Left hand drive vehicles

Connect the cable harness terminals in the connector as follows.

Right-hand drive vehicles

Connect the cable harness terminals in the connector as follows.

All vehicles

Disconnect the connector, if applicable.

Attach the connector to the wiring harness.

Use: , Electrical tape

The connector is not to be used.

Disconnect the connectors.

The part is not to be reused.

Install component that comes with the accessory kit.

Connect the connectors.

Connect the prerouted cable.

All vehicles

Place the Bumper Cover in position for installation.

Left hand drive vehicles

Connect the connectors.

Right-hand drive vehicles

Connect the connector.

Connect the connector.

Vehicles with headlamp washers

Reinstall the removed parts in reverse order.

All vehicles

Reinstall the bumper.

Download software (application) for the accessory's function according to the service information in VIDA.

Reinstall the removed parts in reverse order.